AMC0311SDWVR
Product Specifications
AMC0311SDWVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The AMC0311SDWVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AMC0311SDWVR 2.25 V input isolated amplifier with a single ended output in the eight pin DWV body
The AMC0311SDWVR is the reinforced member of the AMC0x11S line, an isolated amplifier with a 2.25 V high impedance input, a fixed gain of one and a single ended output. The single ended output is the difference that matters against the older differential parts: the signal can go straight into a single ended converter input without a difference amplifier, which removes one op amp, its resistors and its offset trim from the low side of the board.
The input resistance is 2.4 gigohm typical, which is the number that lets a divider run at high impedance without a buffer. The voltage on the REFIN pin sets the output level at zero input, so the zero point of the measurement is a resistor choice rather than a fixed internal value. That is a small feature with a large practical effect, because it lets the same part serve a unipolar channel and a channel that has to sit at mid scale.
Key parameters taken from the AMC0311SDWVR document
| Input range | 0 V to 2.25 V linear, high impedance, fixed gain 1 V per V |
| Input resistance | 2.4 gigohm typical, which is what allows a megohm divider without a buffer |
| Output | Single ended, with the zero input level set by the voltage on the REFIN pin |
| Offset error | Plus or minus 1 mV maximum, with plus or minus 30 microvolt per C of drift |
| Gain error | Plus or minus 0.25 percent maximum, with plus or minus 50 ppm per C of gain drift |
| Nonlinearity | Plus or minus 0.08 percent maximum |
| Signal to noise | 75 dB typical at 1 kHz and 80 dB at 10 kHz, over a 100 kHz window |
| Bandwidth | 120 kHz typical and 145 kHz maximum |
| Common mode transient immunity | 150 V per nanosecond minimum, the highest figure in this family |
| Supplies | High side 3.0 to 5.5 V, low side 3.0 to 5.5 V, both fully specified over the range |
| Undervoltage detection | High side trips at 2.4 V rising and 2.2 V falling, so the output is defined below the operating floor |
| Isolation | 5000 V RMS reinforced in the DWV body, 3000 V RMS basic in the narrow D body for the AMC0211S |
| Temperature | Minus 40 to plus 125 C |
| Order code facts | AMC0311SDWVR, SOIC DWV eight pins, 1000 pieces on a large reel, moisture level 2 with a one year floor life, marking AMC0311S |
| Emissions | Meets CISPR-11 and CISPR-25 limits, which covers both industrial and automotive adjacent equipment |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The single ended output changes the low side bill of materials and the error budget at the same time. A differential output needs a difference amplifier or a differential converter input, and both cost offset, gain mismatch and board area. A single ended output removes those parts and their tolerances, and it leaves the reference and the converter as the only error sources after the amplifier. On a channel that measures a bus voltage for monitoring rather than for protection, that is usually the right trade.
REFIN is the pin to think about before the converter is chosen. The output at zero input equals the REFIN voltage, so a REFIN at ground gives a unipolar channel from 0 to 2.25 V, and a REFIN at 1.25 V gives a channel centred at 1.25 V with a plus or minus 2.25 V span, which only fits a rail above 3.5 V. The same part therefore serves two different converter conventions, and the choice has to be made with the converter window and the supply rail in front of the reader.
The 150 V per nanosecond transient immunity is the highest in the family, and it is what makes this part usable next to a fast switching node. A silicon carbide half bridge can move several hundred volts in a few tens of nanoseconds, which is exactly the edge this rating describes. The amplifier will still produce a small output perturbation at the edge, which is why the converter sampling instant and the input filter both matter, but the channel recovers rather than latching, and the control loop does not see a step it has to fight.
The reinforced and basic variants share a family and a transfer function, and they differ in the package and the barrier. The AMC0311S is the reinforced member in the wide body, and the AMC0211S is the basic member in the narrow body. A board that has to move from basic to reinforced changes the body and the isolation file, and a board that moves the other way saves area and cost but has to reopen the same file. The electrical table is the same, which is why the substitution looks easier than it is.
- Divider impedance against the 2.4 gigohm input resistance and the leakage of the board around it.
- Zero point on first article with the REFIN resistor fitted, against the converter code the firmware expects.
- Offset with the input grounded at the high side, and again with the high side supply removed.
- Output perturbation at the switching edge, sampled at the instant the converter actually converts.
- REFIN divider tolerance, because the zero point error doubles as a full scale error if the reference is shared.
- Isolation and creepage on the assembled board, for the reinforced variant in particular.
Which projects this part fits
This part fits isolated bus voltage monitoring in motor drives and inverters, DC link measurement in chargers and photovoltaic converters, battery stack monitoring, isolated supply supervision in medical equipment and industrial control, and any channel where a single ended converter is already on the board. It is the practical choice where the low side has a single ended converter with a spare channel, and where adding a difference amplifier would cost more than the isolation itself. For customers upgrading from a differential isolated amplifier, this part removes parts rather than adding them, which is unusual in a safety related change.
Questions that come up before a purchase order is released
Does the single ended output lose the noise immunity of a differential pair?
It loses the common mode rejection that a differential pair gives on the low side, and it keeps the barrier immunity that the isolation provides. In practice the low side is a short trace to a converter on the same ground, so the common mode it would reject is small. A long ribbon between the amplifier and the converter is the case where the differential version is still the better answer.
What sets the output at zero input?
The voltage on REFIN. With REFIN at ground the channel is unipolar, and with REFIN at a positive voltage the channel is offset by that voltage. The REFIN source has to be quiet and stable, because any error there appears directly as a zero point error and is indistinguishable from amplifier offset in the final reading.
Is this part a drop in replacement for the AMC1311?
No, for two reasons. The input range is 2.25 V rather than 2 V, and the output is single ended rather than differential. The pins line up in the same body, which is where the confusion comes from, and the transfer function and the output topology are both different. A board that substitutes one for the other needs the divider ratio and the converter input reworked, not just the part number.
How does the undervoltage detection behave?
The high side trips at 2.4 V rising and 2.2 V falling, so a rail that is collapsing produces a defined output rather than a floating one. Firmware should treat that output as a diagnostic, the same way it treats a missing supply on the differential parts. The threshold is also a warning for a 3.3 V rail with a long rise time, because the amplifier is not valid until the rail passes 2.4 V.
What is the difference between the S suffix family members?
The AMC0211S and the AMC0311S are the basic and reinforced members of one family. They share the input stage, the gain, the drift and the transient immunity, and they differ in the package and the barrier rating. The reinforced part is the one to quote for a mains connected measurement, and the basic part is for a measurement where the barrier is inside a double insulated enclosure.
How SUPERB handles this line
We supply the AMC0311SDWVR from original reels with lot traceability and check the family marking, because the basic and reinforced members share a transfer function and look alike in a reel. The power management cross reference page lists the isolated measurement families with their converter side, ADC and DAC cross reference covers the single ended converters that read this output, and how to verify a drop in replacement sets out the checks a substitution like this one needs before a line changes over.