ADS61B49
Product Specifications
ADS61B49
Texas Instruments — Power Management & Signal Chain
Product Overview
The ADS61B49 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADS61B49: 14 bit 250 MSPS converter with an integrated analog input buffer in a 48 pin QFN
ADS61B49 is the 14 bit member of the buffered 250 MSPS pair, sharing a pin out with the 12 bit part so one board can carry either grade in a QFN body of 48 pins. The ADS61B49 samples one channel at 250 MSPS with 14 bit resolution and the same integrated high impedance analog input buffer as its 12 bit sibling. Total power is 790 mW and the output is DDR LVDS or parallel CMOS. The document states a 2 V peak to peak differential input range, a programmable 1 V peak to peak full scale, a 2.3 V input common mode and pin compatibility with the ADS6149 family.
Order code and package
| Order code | ADS61B49 |
| Channels | one |
| Resolution | 14 bit |
| Maximum sample rate | 250 MSPS |
| Input buffer | integrated, high impedance |
| Differential input range | 2 V peak to peak |
| Input common mode | 2.3 V |
| Full scale option | 1 V peak to peak, programmable |
| Output interface | DDR LVDS or parallel CMOS |
| Package | 48 pin QFN, 7 mm by 7 mm |
| Total power | 790 mW at 250 MSPS |
| Document | ADS61Bx9 family data sheet |
Electrical parameters that decide the application
| Quantisation floor | about 86 dBFS for an ideal 14 bit converter |
| Power per sample | 3.16 nJ at 250 MSPS |
| Data rate at 14 bit | 3.5 Gbps at 250 MSPS, before framing |
| Gain error, reference | minus 2.5 to plus 2.5 percent of full scale |
| Gain error, channel | 0.2 percent of full scale |
| Gain drift | 0.001 percent of full scale per C |
| Offset drift | 0.005 mV per C |
| Clock amplitude | 400 mV peak to peak minimum, differential |
| Programmable gain | up to 6 dB |
| Sibling part | ADS61B29, 12 bit, same body and pin out |
| Pin compatibility | ADS6149 family |
| Temperature | minus 40 to 85 C |
Points to check before this part goes on a BOM
Fourteen bits raises the ideal quantisation floor to about 86 dBFS, which is 18 dB below the 12 bit sibling. In practice the converter noise and the clock jitter decide where the floor actually lands, so the extra two bits pay off only when the clock and the analog front end are good enough to use them.
The common mode of 2.3 V is called out in the document as different from the ADS6149 family, and that note applies to this part as much as to the 12 bit one. A drive network borrowed from an older board biases the input at the wrong point and the loss appears as reduced swing, not as a fault.
At 250 MSPS and 14 bit the data rate is 3.5 Gbps, so the same package and the same 790 mW now carry 25 percent more data than the 12 bit part. The capture device has to accept the wider word, which is the only change on the digital side but it is a real one for an existing board.
The 2 V peak to peak differential range with a programmable 1 V peak to peak full scale is a trade the user makes at the register level. Halving the full scale halves the input noise requirement on the drive amplifier and costs 6 dB of SNR, which is often the right choice behind a passive filter with limited gain.
The buffered input means the source sees a high impedance load, so the filter in front of the converter behaves the way the filter simulation says it does. That is the practical reason to select this part over a non buffered converter at the same rate, and it is worth more than the data sheet noise difference in most receiver chains.
Gain error of plus or minus 2.5 percent from the internal reference dominates the error budget. At 14 bit that is 410 codes of full scale, far more than the resolution, so any absolute amplitude requirement has to be met by calibration or by an external reference.
Two grades in one body is the buying argument for this family. A product line can ship the 12 bit part on cost sensitive builds and the 14 bit part on performance builds from one board, provided the register loading and the capture word width are handled in firmware from the start.
The output mode is a pin count decision at this rate. In CMOS the 14 bit word is 14 data lines plus a clock at 250 MHz, which most capture devices will not accept, so the LVDS path is the practical one and the board has to carry a differential receiver with the right input delay. Keeping the same part in the same socket and changing only the output mode is possible, but the two modes are not the same board.
Where this order code fits
This order code fits multicarrier cellular receive paths, radar digitisation with a modest instantaneous bandwidth, test and measurement digitisers and power amplifier linearisation loops where 12 bit is not enough headroom against a strong blocker. The buffered input makes it usable behind a passive filter or a long cable where the sampling current cannot be supplied directly. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Is the 12 bit part a drop in replacement when 14 bit is not needed? The pin out and the body match, so the board works, but the word width and the register map have to be handled by the capture logic and the firmware.
Does the buffer remove the need for an external amplifier? It removes the need to supply the sampling current. A passive filter can drive it directly, which is often enough for a receiver channel.
What limits the usable resolution at 250 MSPS? The clock jitter and the analog front end noise. The converter itself gives 14 bit words; whether the last two bits carry information depends on what is in front of it.
SUPERB quotes this order code with grade, date code and packing stated on the offer, and the Defense Grade Components page sets out the checks that keep a 250 MSPS substitution from failing on the bench.