ADS5463
Product Specifications
ADS5463
Texas Instruments — Power Management & Signal Chain
Product Overview
The ADS5463 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADS5463: 12 bit 500 MSPS converter with an on chip analog buffer in an 80 pin TQFP
ADS5463 is a 500 MSPS 12 bit converter with an integrated analog buffer, three and a half clock cycles of latency and a 2.3 GHz input bandwidth in a TQFP body of 80 pins. The ADS5463 samples one channel to 12 bit at 500 MSPS with an on chip analog buffer, a 2.3 GHz input bandwidth and 77 dBc of spurious free dynamic range at a 300 MHz input. Latency is stated as 3.5 clock cycles, the outputs are LVDS compatible, total power is 2.2 W and the body is an 80 pin TQFP with an exposed pad. The same document covers the ADS54RF63, which is the 550 MSPS member of the pair.
Order code and package
| Order code | ADS5463 |
| Channels | one |
| Resolution | 12 bit |
| Sample rate | 500 MSPS |
| Sibling part | ADS54RF63 at 550 MSPS, same document |
| Input buffer | on chip analog buffer |
| Input bandwidth | 2.3 GHz |
| Output interface | LVDS compatible |
| Latency | 3.5 clock cycles |
| Package | 80 pin TQFP with exposed pad |
| Total power | 2.2 W |
| Document | SLAS515E, November 2006, revised July 2009 |
Electrical parameters that decide the application
| SFDR | 77 dBc at a 300 MHz input |
| SNR | see the electrical table for the input frequency in use |
| Input bandwidth | 2.3 GHz |
| Latency | 3.5 clock cycles |
| Temperature | industrial, minus 40 to 85 C |
| Pin compatibility | similar to the ADS5440, ADS5444 and ADS5474 family |
| Digital correction | on chip, three stage pipeline with correction |
| Power per sample | 4.4 nJ at 500 MSPS |
| Clock | differential, half rate output clock supplied |
| Thermal vias | 36 vias in a 6 by 6 array, per the vendor note |
| Input drive | differential, with the on chip buffer |
| Package family | TQFP with exposed pad, not a QFN |
Points to check before this part goes on a BOM
Latency of 3.5 clock cycles at 500 MSPS is 7 ns, which is the number that decides whether this converter can sit inside a control loop. A pipelined converter with ten cycles of latency is a capture device only; this one can close a loop around a power amplifier because the delay is a fraction of the loop period at typical modulation rates.
The 2.3 GHz input bandwidth allows direct digitisation of a high intermediate frequency, which removes a mixer stage and its local oscillator from the signal chain. The trade is that the clock jitter requirement becomes severe: at 500 MSPS and a 1 GHz input, a jitter of one picosecond alone limits the SNR to about 50 dB.
77 dBc of SFDR at a 300 MHz input is quoted at a specific frequency and the number falls as the input moves higher. A receiver that plans to digitise at 900 MHz should read the curve in the document rather than the feature line, because the difference between 300 MHz and 900 MHz is several dB of spur margin.
An on chip analog buffer means the sampling network does not present a switched capacitor load to the source, which is what makes a passive front end possible at 500 MSPS. The buffer also sets the input common mode, so a transformer coupled front end has to be biased to that point rather than left floating.
2.2 W in an 80 pin TQFP with an exposed pad, and the vendor note calls for a 6 by 6 array of 36 thermal vias. A TQFP pad is large enough that the solder voids are the usual cause of a hot part, so the reflow profile and the paste pattern belong in the process documentation, not only in the datasheet folder.
The pin out is stated as similar to the ADS5440, ADS5444 and ADS5474 family, which is an upgrade path within a family rather than a drop in substitution. Pin similarity means the board can be adapted; it does not mean an unverified part can be fitted to a qualified assembly.
The industrial version covers minus 40 to 85 C, and the enhanced product release of the same converter exists for military programmes. The die may be shared but the qualification, the baseline control and the change notification are not, so the two order codes are not interchangeable in a programme that requires the enhanced flow.
The same document covers the ADS54RF63 at 550 MSPS, which is the faster member of the pair and shares the body and the interface. A board built around this converter can take the faster part if the clock and the thermal path allow it, which makes the pair useful when a programme needs to move up in rate without a board change.
Where this order code fits
This order code belongs on radar and electronic warfare receivers, software defined radio boards, test and measurement instruments and power amplifier linearisation loops where a 500 MSPS capture with low latency is required. The 3.5 cycle latency is what makes it usable inside a control loop rather than only in a capture path. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Defense Grade Components page.
Questions buyers ask
What is the latency and why does it matter? 3.5 clock cycles, about 7 ns at 500 MSPS. That is short enough to use the converter inside a control loop rather than only in a capture path.
Does the on chip buffer mean any source can drive it? It removes the sampling current from the source, which is what allows a passive front end. The source still has to meet the distortion and noise the 12 bit resolution expects.
Is this package a QFN? No, it is an 80 pin TQFP with an exposed pad, which is a different assembly and rework process from a QFN.
SUPERB supplies this order code with the date code and packing on the offer, and the Obsolete RF Part Replacement page covers the checks that keep a high speed converter socket supplied over a long programme.