Contact Us

ADC10040

Brand: Texas Instruments
Texas Instruments ADC10040 is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADC10040 — Power Management & Signal Chain | Superb Automation

ADC10040

Texas Instruments — Power Management & Signal Chain

Product Overview

The ADC10040 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ADC10040: 10 bit 40 MSPS converter on a single 3 V rail at 55.5 mW

ADC10040 is a low power 10 bit pipeline converter with a selectable full scale input and a standby mode that drops consumption to 13.5 mW in a TSSOP body of 28 pins. The ADC10040 converts one channel to 10 bit words at 40 MSPS from a single 3 V supply, dissipating 55.5 mW at full rate and 13.5 mW in standby. The input full scale can be selected as 2.0, 1.5 or 1.0 V peak to peak, the analog bandwidth is 400 MHz, and the converter uses a differential pipeline with digital error correction and an on chip sample and hold. Typical SNR at an 11 MHz input is 59.6 dB and typical DNL is plus or minus 0.3 LSB. The body is a 28 pin TSSOP.

Order code and package

Order codeADC10040
Channelsone
Resolution10 bit
Conversion rate40 MSPS
Supplysingle 3.0 V rail
Full scale2.0, 1.5 or 1.0 V peak to peak, selectable
Analog bandwidth400 MHz, minus 3 dB
Power at 40 MSPS55.5 mW
Standby power13.5 mW
Package28 pin TSSOP
Architecturedifferential pipeline with digital error correction
DocumentSNAS224M, July 2003, revised April 2013

Electrical parameters that decide the application

SNR59.6 dB typical at an 11 MHz input
DNLplus or minus 0.3 LSB typical
Analog bandwidth400 MHz at minus 3 dB
Power per sample1.39 nJ at 40 MSPS
Standby reductionabout 76 percent below the active figure
Input configurationdifferential, on chip sample and hold
Full scale optionsthree, strapped or programmed
Data rate at 10 bit400 Mbps at 40 MSPS
Interfaceparallel output
Temperatureas stated in the document for the commercial and industrial grades
Supply range3.0 V nominal, see the recommended operating table
Familythe Q version in the same document carries the automotive flow

Points to check before this part goes on a BOM

The selectable full scale of 2.0, 1.5 or 1.0 V peak to peak is a front end decision made at the converter. A 1 V range doubles the resolution per code but halves the headroom, so an input stage with a fixed 2 V output should keep the 2 V setting and a stage with a 1 V output should use the 1 V setting. Using the wrong one costs either signal to noise or clipping.

Standby at 13.5 mW against 55.5 mW active is a 76 percent saving and it is what makes this part fit a duty cycled product. The wake up time between standby and a valid sample is the number to check for a burst application, because the power saving is only real if the part can be woken inside the sampling window.

59.6 dB of SNR at 11 MHz against an ideal 10 bit floor of 62 dBFS leaves about 2.4 dB of implementation loss, which is a good result for a part in this class. The takeaway is that a system built on it cannot claim better than about 9.6 effective bits, and the analog front end should be planned for that figure rather than for 10.

A 400 MHz analog bandwidth on a 40 MSPS converter means undersampling is possible. Capturing a 100 MHz intermediate frequency directly is a real option, provided the clock and the input filter are clean, and it can remove a mixer from a low power receiver.

DNL of plus or minus 0.3 LSB typical is a linearity statement rather than a guaranteed limit, and it is quoted as typical. A board that needs monotonicity guaranteed at every code and temperature should look at the maximum column in the electrical table and at the test limits offered on the order.

The 28 pin TSSOP is a package type that is still easy to rework and inspect, which matters for small production runs and for instruments that are repaired rather than replaced. It is one of the few remaining low pin count converters in a leaded package at this rate, and that is often the reason it is selected.

This document has been revised many times since 2003 and the part sits in a long lived rate class. For a product with a ten year service life, that history is usually a better sign than a newer part with no track record, and the automotive grade in the same document extends the usable range.

A 28 pin TSSOP keeps the solder joints visible and the rework process standard, which matters for instruments that are repaired rather than replaced. It is also a package that a small production run can assemble without x-ray inspection, and at this rate class that is a real advantage over a QFN.

Where this order code fits

This order code fits portable instruments, battery powered data loggers, ultrasound and optical front ends with a modest channel count, and industrial monitoring boards where 10 bit at 40 MSPS is enough and the power budget is the deciding constraint. The selectable full scale makes it usable behind either a 2 V or a 1 V drive stage without an extra amplifier. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the How to Reduce Component Cost page.

Questions buyers ask

What does the full scale selection change? The input range: 2.0, 1.5 or 1.0 V peak to peak. A smaller range gives finer resolution per code and less headroom.

Is the standby mode usable in a duty cycled product? It drops consumption to 13.5 mW from 55.5 mW. Whether it saves energy depends on the wake up time against the sampling window.

Can it digitise a signal above 20 MHz? Yes, the 400 MHz analog bandwidth supports undersampling. The clock and the anti alias filter have to be planned for it.

SUPERB supplies this order code with packing and date codes, and the BOM Shortage Recovery page covers how to keep a low power converter socket supplied when the original line is short.