Contact Us
  • Home
  • COMPONENTS
  • Tamper Evident Seals and Security Labels for Enclosures

Tamper Evident Seals and Security Labels for Enclosures

Plastic pull tight seals, fixed and adjustable, from 13 lbf to 40 lbf, for cabinet doors, meter boxes, tote boxes and service hatches. High security bolt seals to ISO 17712:2013 with pull apart strength from 4,100 lbf to 6,475 lbf for containers and trailers. Numbered, bar coded and printed security labels are supplied with the customer artwork on the same order.
quote now

Product Specifications

Product Overview

A seal does two jobs and only one of them is physical. The physical job is to keep a door closed long enough for a casual attempt to be obvious. The second job is evidence: a numbered seal that is recorded when it is fitted and checked when it is removed turns a door into a record.

That is why the strength of a plastic seal is modest and its numbering is not. A pull tight seal at 18 lbf to 40 lbf does not stop a determined person for more than a few seconds, but a cut strap cannot be rejoined without the number sequence showing a gap. The record is the control, and the seal is the token that makes the record possible.

Two levels are used on equipment. Indicative seals, which are the plastic adjustable and fixed length straps, cover cabinets, meter boxes, service hatches and tote boxes. High security bolt seals, which are tested to ISO 17712:2013 and carry the H mark, cover containers, trailers and any load that crosses a customs boundary.

Security labels sit alongside the seal. A printed label that leaves a void message when it is peeled does the same job on a smaller surface, an access panel, a card slot or a firmware cover, and it can carry a serial number and a bar code so the same record can be kept without a strap. Labels are printed to the customer artwork and are quoted with the seal so the numbering scheme is one scheme.

Key Specifications

ParameterIndicative plastic sealsHigh security bolt seals
ApplicationCabinets, meter boxes, tote boxes, service hatchesContainers, trailers, rail cars, customs loads
Body materialHDPE strap with an acetal locking mechanismCarbon steel bolt, ABS or steel locking body
Strength13 lbf to 40 lbf average pull apart4,100 lbf to 6,475 lbf average pull apart
StandardIndicative, not tested to ISO 17712ISO 17712:2013 and C-TPAT where stated
MarkingHeat stamped name and consecutive numbers, optional bar codeLaser or cold stamped, consecutive body and bolt numbers
RemovalHand, or a tear away tab on some partsBolt cutter or a dedicated removal tool
WeatherHDPE and acetal hold through cold and heatZinc chromate finish on the steel
NumberingConsecutive on the strap or the flagConsecutive on the body, matching the bolt
PackStrips of 10, boxes of 1000Boxes of 200

Included Models and Order Codes

The plastic seals are listed by strap length, because the operational length is shorter than the overall length and the difference is the part that goes into the lock. A 12 in seal gives about 9 in of usable loop. The bolt seals are listed by the strength that the maker publishes, and the length is the bolt length, not the sealed gap.

SealTypeOverall lengthOperational lengthStrap or boltStrength
All SealAdjustable, light duty8 in (203 mm)5 in (127 mm)2.8 mm strap18 lbf (8.2 kgf)
All SealAdjustable, light duty10 in (254 mm)6.4 in (162 mm)2.8 mm strap18 lbf (8.2 kgf)
Pull-Tite IIAdjustable, self locking9 in (228 mm)9 in, over 20 locking positions3 mm strap13 lbf
Tug-TightAdjustable, medium duty9 in (229 mm)6 in (152 mm)3.5 mm strap40 lbf (18.1 kgf)
Tug-TightAdjustable, medium duty12 in (305 mm)9 in (229 mm)3.5 mm strap40 lbf (18.1 kgf)
Tug-TightAdjustable, medium duty15 in (381 mm)12 in (305 mm)3.5 mm strap40 lbf (18.1 kgf)
Tug-TightAdjustable, medium duty18 in (457 mm)15 in (381 mm)3.5 mm strap40 lbf (18.1 kgf)
Tug-Tight tear awayAdjustable, removable by hand12 in (305 mm)9 in (229 mm)3.5 mm strap30 lbf (13.6 kgf)

High Security Bolt Seals to ISO 17712

A bolt seal is a two part device: a hardened steel bolt and a locking body. The bolt is pushed in once and the locking insert spins free afterwards, which is the visual proof that it has not been opened. The H mark on the body is what a customs officer looks for, and the number on the bolt has to match the number on the body, because a seal that has been replaced with a matching body is the failure mode these seals exist to stop.

SealBody materialBoltStrengthStandardRemoval
Intermodal IICarbon steel, zinc chromate, ABS cover89 mm x 9.5 mm4,713 lbf (21.0 kN)ISO 17712:2013, C-TPATBolt cutter
SnapTrackerSteel bolt, keyed body63.5 mm4,200 lbf (18.68 kN)ISO 17712:2013, C-TPATBolt cutter
Econo BoltCarbon steel, 8 mm lock body78.6 mm x 7.9 mm4,100 lbf (18.24 kN)ISO 17712:2013Bolt cutter
Super BoltHardened steel, zinc plated102 mm or 152 mm x 7.9 mm6,475 lbf (28.80 kN)ISO 17712:2013Dedicated tool

Key Features

Numbering as the control – Each seal carries a consecutive number that is written on the record when it is fitted, so a missing number is visible without opening the door.

Two strength classes – 13 lbf to 40 lbf for a cabinet and 4,100 lbf to 6,475 lbf for a container, chosen by what the seal has to survive rather than by habit.

Adjustable length – A pull tight strap can be cinched to the latch it passes through, so one part number covers several door thicknesses.

Tear away option – A Tug-Tight with a tear away tab comes off by hand at 30 lbf, which avoids a cutter at every service visit.

ISO 17712 and C-TPAT – The bolt seals carry the standard and the H mark that a customs check looks for, with matching numbers on bolt and body.

Marking options – Heat stamped name and number, laser bar code or a printed flag, so the seal can be read by the same system as the label.

Security labels on the same order – Printed void labels carry a serial and a bar code where a strap will not fit, and the numbering scheme is kept in one place.

Packs that match the job – Strips of 10 and boxes of 1000 for the plastic seals, boxes of 200 for the bolt seals, so a small site is not forced into a carton.

Applications

Seals are used where a door has to be provably closed rather than locked. The four cases below cover most of the orders.

Meter boxes and service cabinets – A 12 in pull tight seal through the latch, numbered and recorded, shows whether the cabinet was opened between two readings.

Tote boxes and returnable containers – A short All Seal on the latch is enough for a tote that travels between two sites, and the tear away version comes off without a cutter.

Containers and trailers – An Intermodal II or a Super Bolt with matching bolt and body numbers is what a customs check and a C-TPAT audit expect to see.

Access panels and firmware covers – A printed void label over the screw head shows whether a panel was opened, on a surface too small for a strap.

A seal is only evidence if the number is written down, so the SUPERB PCB shipping checklist carries the seal range and the label range on the same line as the serial number. On the SUPERB PCBA build the seal goes on after the final test and the number is copied to the test record, which is what makes a later claim checkable.

Sourcing and Cross-Reference

The seal and the record are ordered together. A box of 1000 seals without a numbering range on the purchase order arrives with numbers that overlap the last box, and the record then has two seals with the same number. The range is quoted with the box and written on the packing list.

Strength is chosen by the application, not by the price. A 40 lbf strap on a cabinet is generous; a 4,700 lbf bolt seal on a tote box is money spent on a load that will never see a customs officer. The two classes exist because the jobs are different.

Labels are printed to artwork. The void message, the size, the adhesive and the serial range are confirmed before the run, because a label that peels cleanly off an anodised panel is worse than no label: it looks like control and provides none.

SUPERB Assembly fits the seal through the latch, crimps or cinches it to the strap length on the drawing and records the number, because a seal that is looped twice can be opened and closed again without cutting it.

Q: Can you supply 1,000 Tug-Tight seals in the 12 in length with consecutive numbers from 045001, and 500 void labels numbered to match?

A: Send the door or latch type, the number of seals, the strength class and the serial range you need. The SUPERB Tech desk replies with the seal, the label and the numbering, and confirms whether the seal is indicative or ISO 17712.

Why Buy Security Seals Through SUPERB

  1. Numbering range on the order: The consecutive range is quoted and printed on the packing list, so two boxes never carry the same number.
  2. Strength matched to the job: Indicative straps for cabinets and ISO 17712 bolt seals for containers, quoted against the risk rather than the price.
  3. Seal and label in one scheme: Printed labels carry the same serial sequence as the seals, so the record is kept in one place.
  4. Standard evidence: ISO 17712:2013 and C-TPAT are stated on the part that carries them, with the H mark and matching numbers.
  5. Packing for the site: Strips of 10 and boxes of 1000 let a small service team work from the same part number as a depot.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Cable Markers and Wire Labels for Harness Identification, Cam Locks and Key Locking Latches for Enclosure Doors, Draw Latches and Toggle Latches for Enclosure Doors, Captive Panel Screws and Quarter Turn Fasteners, Date Code Management and Traceability, Incoming Inspection Plan.