Contact Us
  • Home
  • COMPONENTS
  • Enclosure LED Lamps and Door Switches for Cabinet Lighting

Enclosure LED Lamps and Door Switches for Cabinet Lighting

LED system lights from 400 to 1200 lumens in four body lengths. 100 to 230 V AC, 24 V DC and 24 to 56 V DC versions share one mounting pattern. Door-operated switches, motion detectors and through-wiring accessories. IP20 interior lights with a turnable Fresnel cover for even panel lighting.
quote now

Product Specifications

Product Overview

An enclosure light is judged on two numbers: how much of the light reaches the back of the panel, and how much heat it adds to the air that the climate control has to remove. A 900 lumen light drawing 11 W adds 11 W to the cabinet load, which is why the LED generation replaced the 25 W fluorescent fittings in most panels rather than only saving energy.

The Rittal LED system light range covers 400, 600, 900 and 1200 lumens in body lengths of 262, 337 and 437 mm. The cover carries a Fresnel structure that spreads the beam along the panel, and it can be turned so the light follows the mounting position rather than the other way around. Light colour is 4000 K neutral white across the range.

The light is half of the job. A door-operated switch cuts the supply when the door closes, so the light does not run all shift and does not blind the operator when the door opens. The switch is a separate part, and the current rating decides whether it can carry the light directly or needs a contactor.

Key Specifications

SeriesLuminous fluxRated voltagePowerLengthLight colourProtectionOperating temperature
SZ 2500.100400 lm100 - 230 V AC-262 mm4000 KIP20-20 to 55 C
SZ 2500.110600 lm100 - 230 V AC7 W337 mm4000 KIP20-20 to 55 C
SZ 2500.200900 lm100 - 230 V AC11 W437 mm4000 KIP20-20 to 55 C
SZ 2500.220900 lm24 V DC-437 mm4000 KIP20-20 to 55 C
SZ 2500.3001200 lm100 - 230 V AC13 W437 mm4000 KIP20-20 to 55 C
SZ 2500.3201200 lm24 - 56 V DC-437 mm4000 KIP20-20 to 55 C

Included Models and Order Codes

Sockets and motion detectors are the two options that change the part number rather than the light output. Socket versions take a country-specific outlet, which is why one 900 lumen light has five order codes.

Part numberVersionRated voltageSocketLength
2500.100Without socket100 - 230 V AC-262 mm
2500.110Without socket100 - 230 V AC-337 mm
2500.200Without socket100 - 230 V AC-437 mm
2500.210With socket100 - 230 V ACType F, CEE 7/3437 mm
2500.211With socket100 - 230 V ACType G, BS 1363437 mm
2500.214With socket100 - 125 V ACType B, NEMA 5-15437 mm
2500.220Without socket24 V DC-437 mm
2500.300Motion detector100 - 230 V AC-437 mm
2500.310Motion detector, socket100 - 230 V ACType F, CEE 7/3437 mm
2500.320Motion detector24 - 56 V DC-437 mm
2500.460Door switch, 800 mm cable230 V AC / 24 V DC, 1 A-800 mm
4127.010Door switch, no cable240 V AC 6 A / 125 V DC 8 A--

Connection Accessories

Infeed and through-wiring parts let several lights run from one supply without a terminal box inside the cabinet. The 3-pole parts are for 100 to 230 V AC, the 2-pole parts for 24 V DC.

Part numberFunctionPolesCable lengthPack
2500.400Infeed for 100 - 230 V AC3-pole3000 mm5 pcs
2500.430Through-wiring for 100 - 230 V AC3-pole3000 mm5 pcs
2500.410Infeed for 24 V DC2-pole3000 mm5 pcs
2500.440Through-wiring for 24 V DC2-pole3000 mm5 pcs
2500.490Magnet mounting kit--2 pcs
2500.660Connection cable for door switch-3000 mm1 pc

Key Features

Turnable Fresnel cover – two structures on one cover, so the beam can be sent down the panel or across the door without changing the mounting position.

4000 K neutral white – one light colour across the range, so a panel with mixed lengths still reads the same colour.

24 V DC and 24 to 56 V DC versions – for panels that run a battery or a DC bus and cannot take a mains feed to the door.

Motion detector versions – the 1200 lumen models switch on when the door opens and off after the set delay, with no door switch to wire.

Protection class II – all-insulated body, rated insulation voltage 300 V AC, impulse withstand 2500 V AC phase to earth.

Three mounting methods – screw to the 25 mm pitch pattern, clip to the frame section, or hold with the magnet kit on a painted panel.

Applications

Cabinet lighting is bought with the enclosure, not after the panel is wired. Three patterns repeat.

Control and automation cabinets – 900 and 1200 lumen lights in 437 mm bodies, switched by the door, with the socket version for a laptop or a tool charger inside the cabinet.

IT and network racks – 24 V DC lights fed from the rack supply, with through-wiring so four lights run from one infeed.

Machine and test enclosures – motion detector models where the door is opened by different operators and no switch can be fitted to the frame.

On a panel build the light, the switch and the wiring are quoted as one line, and the SUPERB PCBA and the SUPERB PCB are checked against the same door drawing before the harness is cut.

Sourcing and Cross-Reference

Match the switch rating to the light, not to the cabinet: 4127.010 carries 6 A at 240 V AC and 8 A at 125 V DC, so one switch can feed several 11 W lights, but the inrush of a group of drivers is what opens a small contact over time.

A 24 V DC light is not a 24 V AC light. The DC versions accept 24 V DC and the 1200 lumen motion version accepts 24 to 56 V DC, which covers a 48 V DC bus without a converter.

Cable length decides the part number: 2500.460 comes with an 800 mm cable for a door hinge run, while 4127.010 has no cable and is wired into the door harness.

Older fluorescent fittings are often obsolete while the mounting holes are still good. Lead time and availability covers the drop-in replacements that fit the same 25 mm pattern.

When the SUPERB Assembly team dresses the door, the switch is fitted before the light so the cable can be cut to the final length rather than looped and tied.

Q: Can the light be switched by the cabinet door without adding a relay?

A: Yes. Send the door thickness and the supply available inside the cabinet; the SUPERB Tech team quotes the light, the switch and the connection cable as a set.

Why Builders Buy Cabinet Lighting From SUPERB

  1. Light and switch in one quote: the light, the door switch and the connection cable are priced as a set, so the door harness is cut once.
  2. Voltage variants for export builds: 100 to 230 V AC, 24 V DC and 24 to 56 V DC share one mounting pattern and one drawing.
  3. Socket and socket-free versions: the same light is available with a country-specific outlet for service work inside the cabinet.
  4. Accessories held together: infeed, through-wiring and magnet kits are quoted with the light rather than found later.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Enclosure Panel Heaters and Thermostats, Cable Entry Plates and Brush Grommets, Filter Fan Units and Exhaust Filters, Component Lead Time Solutions.