Contact Us
  • Home
  • COMPONENTS
  • Digital Potentiometers for Calibration and Gain Trim

Digital Potentiometers for Calibration and Gain Trim

SPI, I2C and up and down digital potentiometers from 32 to 1024 positions, with end to end resistance, tolerance and temperature coefficient per part.
quote now

Product Specifications

Digital potentiometers for calibration and gain control

Product Overview

A digital potentiometer is a resistor string with a switch at every tap, and the wiper is the switch that is closed. That structure explains both its strength and its limits. The strength is that the ratio between the wiper and either end is set by the tap number alone, so a ratiometric measurement stays accurate even when the absolute resistance moves with temperature. The limit is that the end to end resistance is a silicon resistor with a tolerance of 15 to 30 percent, so the part is only predictable when the circuit uses it as a divider rather than as a two terminal resistor.

Interface choice follows from where the trim happens. An SPI part is written once at power up by the host and then left alone, which suits a gain trim in a production test. An I2C part shares a two wire bus with sensors and memory, which suits a module that already has that bus. The three wire up and down parts, like the X9C103, take two microcontroller pins and store the wiper in non volatile memory, so the setting survives a power cycle without any code at start up. That last property is why they still appear in industrial instruments that have no firmware budget for a calibration routine.

Resolution decides whether the trim is fine enough, and the arithmetic is simple: a 256 position part on a 10 k string moves 39 ohm per step, and the same string at 100 positions moves 100 ohm per step. For a gain trim across a narrow range that is fine. For an offset null where the required step is a millivolt in a 5 V span, the string is put in a divider with fixed resistors so that only a fraction of the span is covered, and the step size falls with it.

Key Specifications

ParameterSPI singleI2C dualUp and down with memory
Positions256256 per channel100
End to end resistance5 k, 10 k, 50 k, 100 k10 k, 50 k, 100 k1 k, 10 k, 50 k, 100 k
Resistance tolerance20 percent on the 10 k version20 percent20 percent
Temperature coefficient45 ppm per C on the 10 k part300 ppm per C end to end, 20 ppm ratiometric300 ppm per C end to end, 20 ppm ratiometric
InterfaceSPI, 3 wireI2C, 2 wire, 3 address pinsCS, U/D and INC
Wiper memoryvolatile, loaded at power upvolatilenon volatile, recalled at power up
Supply2.7 V to 5.5 V3 V or 5 V4.5 V to 5.5 V
Terminal voltage0 V to VDD-5 V to 5 V on the up and down parts-5 V to 5 V

Included Models and Order Codes

The order codes below are the parts quoted most often for gain trim, offset null, bias setting and threshold adjustment. State the resistance value, the number of steps, the interface, whether the setting has to survive a power cycle and the voltage across the string, and the part and its divider resistors are confirmed together.

Part NumberPositionsResistanceInterfaceMemoryPackage
AD5160BRJZ1025610 kSPIvolatile, midscale at power upSOT-23-8
AD5160BRJZ100256100 kSPIvolatile, midscale at power upSOT-23-8
MCP4101025610 kSPIvolatilePDIP-8, SOIC-8
MCP42010256 per channel, 2 channels10 kSPIvolatilePDIP-14, SOIC-14, TSSOP-14
DS1803-010256 per channel, 2 channels10 kI2C, 3 address pinsvolatileDIP-16, SO-16, TSSOP-14
DS1803-050256 per channel, 2 channels50 kI2C, 3 address pinsvolatileDIP-16, SO-16, TSSOP-14
X9C10310010 kup and down, 3 wirenon volatile, 100 years retentionSOIC-8, PDIP-8
X9C104100100 kup and down, 3 wirenon volatileSOIC-8, PDIP-8

Key Features

Ratiometric by construction – the wiper position sets a ratio between the two ends of the string, so a 20 percent tolerance on the absolute value does not affect a divider that is read against the same string.

Steps stated in ohms – each row gives the resistance so the step size can be worked out before the board is built, which is 39 ohm per step for a 10 k part with 256 positions.

Non volatile option – the X9C family keeps the wiper in memory and recalls it at power up, so a calibration done at the bench survives a field power cycle with no firmware action.

Dual channel in one package – the DS1803 and the MCP42010 hold two independent strings, which is what a stereo gain pair or an I and Q offset pair needs from one footprint.

Address pins for a shared bus – three address inputs let eight dual parts sit on one I2C bus, so a multi channel instrument does not need a bus expander for its trims.

Wide terminal range – the up and down parts accept -5 V to 5 V on the terminals, which lets them trim a bipolar signal without a level shift.

Low supply current – the AD5160 draws 8 uA, so a trim that is set once does not appear in the standby budget of a battery instrument.

Shutdown and reset – the SPI parts offer a shutdown that opens the wiper connection and a reset that returns to midscale, which is what a fail safe default needs.

Applications

These parts are quoted for circuits that need a setting to be adjustable after the board is built, typically where: The trim part sits next to the amplifier it adjusts, so it is quoted with the SUPERB PCB and the SUPERB PCBA build for that board and the divider resistors around it.

Production gain and offset trim – an instrumentation amplifier gain is set by a resistor ratio, and a 256 position part in the feedback path lets the test bench trim each unit without a laser or a manual screwdriver.

Bias and threshold setting – a comparator threshold or a laser bias is set by a divider, and the non volatile part keeps the value that was found at the bench across every power cycle.

Calibration in a sealed enclosure – an instrument that is potted after calibration cannot take a screwdriver, so the trim is written over the bus and stored in the part that holds it.

Audio and signal level control – a dual part gives two matched channels for a stereo level, and the ratiometric structure keeps the two channels tracking as the temperature moves.

Sourcing and Cross-Reference

Digital potentiometers are often the last part left on a board that is being cost reduced, and the replacement is usually chosen on positions and interface alone. That is where the trouble starts: a part with the same 256 positions but a different end to end resistance changes the step size, and a part with a different wiper resistance changes the loading on the node it trims. Both are visible on a curve and invisible on a part number.

The store behaviour is the second trap. A volatile part comes up at midscale or at zero depending on the family, which means the firmware has to write the trim at every start. A non volatile part comes up at the last value, which means a corrupted memory shows up as an out of range setting rather than as a default. Long life instruments usually want the non volatile version and a plausibility check on the value read back.

Availability is stable for the plastic packages and less so for the older through hole parts, which are still bought for service and for instruments that were built ten years ago. The quotation line states the package, the temperature grade and the batch date, because a service depot cares about the package more than about the price.

For volume builds, SUPERB Assembly support covers the trim step in the test flow, the wiper load check and the reflow profile the small packages need.

Q: Can you supply a digital potentiometer that keeps the same step size when the original value is unavailable?

A: Yes. Send the current part number, the resistance, the positions, the interface and whether the setting has to survive a power cycle, and the SUPERB Tech sales team will confirm the order code and the nearest part that keeps the step size.

Why Buyers Source Digital Potentiometers Through SUPERB

  1. Step size worked out first: the resistance and the positions are read together, so a substitute does not arrive with a coarser step than the trim loop can accept.
  2. Store behaviour stated: volatile and non volatile parts are listed apart, because the start up value is a firmware decision as much as a part decision.
  3. Dual channels matched: two channel parts are quoted as one line for stereo and I and Q trims, so both channels come from the same lot and track with temperature.
  4. Service packages held: through hole and SOIC versions are tracked for instruments that are already in the field, not only for new builds.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Multi-function ICs, Analog switches and multiplexers, Instrumentation amplifiers, Precision operational amplifiers, Pin to pin cross reference.