STM8S208RBT6
Product Specifications
STM8S208RBT6
ST — MCU & Embedded Processors
Product Overview
The STM8S208RBT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM8S208RBT6: 128 Kbyte Flash STM8S MCU in LQFP64
STM8S208RBT6 is the 128 Kbyte Flash member of the STM8S 8-bit line in a LQFP64 body (14 by 14 mm), with 2048 bytes of true data EEPROM, 6 Kbyte of RAM, 52 general purpose I/O, 16 analog inputs and 16 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. The beCAN 2.0B active controller is part of this order code and runs at up to 1 Mbit/s.
Order code and memory
| Order code | STM8S208RBT6 |
| Program Flash | 128 Kbytes |
| Data EEPROM | 2048 bytes, 300 kcycle endurance |
| RAM | 6 Kbytes |
| Package | LQFP64, 14 by 14 mm |
| Pin count | 64 |
| Maximum general purpose I/O | 52 |
| External interrupt pins | 37 |
| High sink outputs | 16 |
| ADC channels | 16 |
| Controller area network | beCAN 2.0B active, 1 Mbit/s |
| Temperature grade | suffix 6, minus 40 to plus 85 C |
Electrical and peripheral parameters
| Supply voltage | 2.95 to 5.5 V |
| Maximum CPU clock | 24 MHz up to 105 C ambient |
| Flash access | zero wait states to 16 MHz |
| Core | Harvard, 3 stage pipeline, 80 instructions, 20 addressing modes |
| Timers | advanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer |
| Analog to digital converter | 10-bit, 16 channels, scan mode, analog watchdog, 14 clock cycles per conversion |
| ADC clock | 1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V |
| Serial interfaces | UART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz |
| Run current | 11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum |
| Low power | halt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off |
| Reset | power-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis |
| Identification | 96-bit unique ID, single wire interface module for debug and programming |
Points to check before this part goes on a BOM
The RB code is the 128 Kbyte, 64-pin member of the CAN group: 52 I/O, 37 external interrupt inputs and 16 analog channels with the reference pins bonded. It is the usual choice when a CAN node needs the full analog front end but not the 68 I/O of the 80-pin body.
The 208 line carries 37 external interrupt pins on this body while the 207R carries 36, because one pin that is a CAN function on the 208 is a plain interrupt input on the 207. That single pin is the kind of difference that only shows up when the pin map is compared.
With 2048 bytes of EEPROM and 128 Kbytes of Flash, the data space is large enough for a configuration block plus a ring buffer of bus events, and the 300 kcycle endurance supports event logging at a modest rate. RAM remains 6 Kbytes, so the ring buffer competes with the stack and the CAN message buffers.
Where this order code fits
CAN connected instruments, drive and servo controllers and building automation nodes that need 16 analog inputs and a reference pin on a 14 by 14 mm footprint. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Obsolete RF Part Replacement page. Both list the resource differences that decide the choice before any code is written.
Questions buyers ask
How many external interrupt pins? 37 on this body, one more than the equivalent 207R part, because of how the CAN pins are shared.
Do I need an external crystal for CAN? For a 1 Mbit/s bus across temperature the clock tolerance has to be tight. The internal 16 MHz RC oscillator is user trimmable but drifts with temperature, so a crystal is the normal choice for a bus with more than a few nodes.
What is the EEPROM size? 2048 bytes, the same as every 208 body from 48 pins upward at 64 Kbytes and above.
SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the Incoming Inspection Plan page walks through the checks that keep a substitute from failing on the bench.