STM8S208R8T6
Product Specifications
STM8S208R8T6
ST — MCU & Embedded Processors
Product Overview
The STM8S208R8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM8S208R8T6: 64 Kbyte Flash STM8S MCU in LQFP64
STM8S208R8T6 is the 64 Kbyte Flash member of the STM8S 8-bit line in a LQFP64 body (14 by 14 mm), with 2048 bytes of true data EEPROM, 6 Kbyte of RAM, 52 general purpose I/O, 16 analog inputs and 16 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. The beCAN 2.0B active controller is part of this order code and runs at up to 1 Mbit/s.
Order code and memory
| Order code | STM8S208R8T6 |
| Program Flash | 64 Kbytes |
| Data EEPROM | 2048 bytes, 300 kcycle endurance |
| RAM | 6 Kbytes |
| Package | LQFP64, 14 by 14 mm |
| Pin count | 64 |
| Maximum general purpose I/O | 52 |
| External interrupt pins | 37 |
| High sink outputs | 16 |
| ADC channels | 16 |
| Controller area network | beCAN 2.0B active, 1 Mbit/s |
| Temperature grade | suffix 6, minus 40 to plus 85 C |
Electrical and peripheral parameters
| Supply voltage | 2.95 to 5.5 V |
| Maximum CPU clock | 24 MHz up to 105 C ambient |
| Flash access | zero wait states to 16 MHz |
| Core | Harvard, 3 stage pipeline, 80 instructions, 20 addressing modes |
| Timers | advanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer |
| Analog to digital converter | 10-bit, 16 channels, scan mode, analog watchdog, 14 clock cycles per conversion |
| ADC clock | 1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V |
| Serial interfaces | UART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz |
| Run current | 11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum |
| Low power | halt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off |
| Reset | power-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis |
| Identification | 96-bit unique ID, single wire interface module for debug and programming |
Points to check before this part goes on a BOM
The R8 is the 64 Kbyte CAN member with 52 I/O, 37 external interrupt inputs, 16 analog channels and both reference pins. Its EEPROM is 2048 bytes even though the Flash is 64 Kbytes, so a product that needs data space does not have to buy the 128 Kbyte part.
The ADC on this body can use an external reference, and the conversion takes 14 clock cycles at an ADC clock of 4 MHz with a 3 to 5.5 V analog supply, or 6 MHz only above 4.5 V. A CAN node that samples 16 channels once per bus cycle should budget 56 microseconds of conversion plus sampling and multiplexer settling.
The one wait state at 24 MHz is the difference between a comfortable interrupt latency and a marginal one on a busy bus. Running the core at 16 MHz with zero wait states is often the better trade for a node whose work is dominated by CAN interrupts rather than arithmetic.
Where this order code fits
CAN nodes with a substantial analog front end such as battery management slaves, multi sensor condition monitors and motor controllers with 16 feedback channels. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page. Both list the resource differences that decide the choice before any code is written.
Questions buyers ask
Is the 64 Kbyte part cheaper than the 128 Kbyte one? Normally yes, and the peripherals are identical apart from Flash size, so the 64 Kbyte part is the default unless the image needs more.
How many CAN messages can it buffer? The controller provides its own message objects, and the driver's RAM buffers come out of the 6 Kbytes. There is no external memory interface on this family.
What is the reset behaviour? Power-on reset releases between 2.65 and 2.88 V rising, brown-out reset sits between 2.58 and 2.73 V with 70 mV of hysteresis, and the core starts at 2 MHz from the internal oscillator divided by 8.
SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the OEM Procurement page walks through the checks that keep a substitute from failing on the bench.