Contact Us

STM8S207SBT6C

Brand: ST
ST STM8S207SBT6C is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM8S207SBT6C — MCU & Embedded Processors | Superb Automation

STM8S207SBT6C

ST — MCU & Embedded Processors

Product Overview

The STM8S207SBT6C from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM8S207SBT6C: 128 Kbyte Flash STM8S MCU in LQFP44

STM8S207SBT6C is the 128 Kbyte Flash member of the STM8S 8-bit line in a LQFP44 body (10 by 10 mm), with 1536 bytes of true data EEPROM, 6 Kbyte of RAM, 34 general purpose I/O, 9 analog inputs and 15 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. There is no controller area network block in this order code; the CAN member of the same body is listed in the cross reference.

Order code and memory

Order codeSTM8S207SBT6C
Program Flash128 Kbytes
Data EEPROM1536 bytes, 300 kcycle endurance
RAM6 Kbytes
PackageLQFP44, 10 by 10 mm
Pin count44
Maximum general purpose I/O34
External interrupt pins31
High sink outputs15
ADC channels9 of 16
Controller area networknot present
Temperature gradesuffix 6, minus 40 to plus 85 C

Electrical and peripheral parameters

Supply voltage2.95 to 5.5 V
Maximum CPU clock24 MHz up to 105 C ambient
Flash accesszero wait states to 16 MHz
CoreHarvard, 3 stage pipeline, 80 instructions, 20 addressing modes
Timersadvanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer
Analog to digital converter10-bit, 9 channels, scan mode, analog watchdog, 14 clock cycles per conversion
ADC clock1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V
Serial interfacesUART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz
Run current11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum
Low powerhalt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off
Resetpower-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis
Identification96-bit unique ID, single wire interface module for debug and programming

Points to check before this part goes on a BOM

The SB code is the 128 Kbyte member of the 44-pin group: 128 Kbytes of Flash, 1536 bytes of EEPROM and 6 Kbytes of RAM with 34 I/O. It is the largest program space available without leaving the 10 by 10 mm body, which is why it appears in products that have outgrown a 64 Kbyte image but cannot afford a board respin.

The package exposes 9 of the 16 analog channels and does not bond the reference pins, and it carries 8 CAPCOM channels. A board that needs a third complementary output pair or a 16 channel scan has to move up to 64 or 80 pins regardless of how much Flash is needed.

The trailing C in T6C follows the temperature field in the ST ordering string. It is matched with the reel or tray label, not interpreted as a memory or temperature grade, and a production file should carry the full string so that a substitution is never made on the base name alone.

Where this order code fits

Products with large fixed program images such as a multi language display, a protocol converter or a data logger with a file system, where 44 pins and 34 I/O are enough for the outside world. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page. Both list the resource differences that decide the choice before any code is written.

Questions buyers ask

Is the die the same as the 128 Kbyte 80-pin part? The memory is the same size but the pin count, analog channel count, high sink count and dissipation rating differ. Firmware ports between them, the board does not.

What is the fastest external interrupt response? An external interrupt wakes the part from wait mode in a few cycles at the CPU clock, and from halt mode after the 52 to 54 microsecond wakeup time plus one LSI clock, as the datasheet wakeup table states.

Does it have CAN? No. The 44-pin CAN member is the STM8S208SB, which carries 128 Kbytes and 1536 bytes of EEPROM on the same body.

SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the BOM Consolidation page walks through the checks that keep a substitute from failing on the bench.