STM8S207M8T6B
Product Specifications
STM8S207M8T6B
ST — MCU & Embedded Processors
Product Overview
The STM8S207M8T6B from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM8S207M8T6B: 64 Kbyte Flash STM8S MCU in LQFP80
STM8S207M8T6B is the 64 Kbyte Flash member of the STM8S 8-bit line in a LQFP80 body (14 by 14 mm), with 2048 bytes of true data EEPROM, 6 Kbyte of RAM, 68 general purpose I/O, 16 analog inputs and 18 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. There is no controller area network block in this order code; the CAN member of the same body is listed in the cross reference.
Order code and memory
| Order code | STM8S207M8T6B |
| Program Flash | 64 Kbytes |
| Data EEPROM | 2048 bytes, 300 kcycle endurance |
| RAM | 6 Kbytes |
| Package | LQFP80, 14 by 14 mm |
| Pin count | 80 |
| Maximum general purpose I/O | 68 |
| External interrupt pins | 37 |
| High sink outputs | 18 |
| ADC channels | 16 |
| Controller area network | not present |
| Temperature grade | suffix 6, minus 40 to plus 85 C |
Electrical and peripheral parameters
| Supply voltage | 2.95 to 5.5 V |
| Maximum CPU clock | 24 MHz up to 105 C ambient |
| Flash access | zero wait states to 16 MHz |
| Core | Harvard, 3 stage pipeline, 80 instructions, 20 addressing modes |
| Timers | advanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer |
| Analog to digital converter | 10-bit, 16 channels, scan mode, analog watchdog, 14 clock cycles per conversion |
| ADC clock | 1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V |
| Serial interfaces | UART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz |
| Run current | 11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum |
| Low power | halt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off |
| Reset | power-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis |
| Identification | 96-bit unique ID, single wire interface module for debug and programming |
Points to check before this part goes on a BOM
The 80-pin body carries 68 I/O, 37 external interrupt inputs and 18 high sink outputs, which is the highest I/O count in the STM8S207 line. Its junction to ambient thermal resistance is 38 C/W for the 14 by 14 mm LQFP, so at 11.4 mA from 5 V the die sits a little over 2 C above ambient and the package rating of 443 mW is not the limit in a normal enclosure.
The EEPROM on this code is 2048 bytes even though the Flash is 64 Kbytes, and that is the same EEPROM size as the 128 Kbyte member. Products that store long calibration records or event logs can therefore pick the cheaper 64 Kbyte part and keep the data space.
The 80-pin body exposes all 16 analog channels and both reference pins. It also brings out the full complement of 9 CAPCOM channels and 3 complementary outputs, which is what a board with several half bridges or a matrix of PWM channels needs.
Where this order code fits
Multi channel industrial controllers, panel boards with large key matrices, and equipment that needs 68 I/O plus 16 analog inputs on one device. Often chosen where a previous board used two smaller MCUs. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page. Both list the resource differences that decide the choice before any code is written.
Questions buyers ask
Why choose 80 pins? For the 68 I/O, the 37 external interrupt inputs and the 18 high sink outputs. The analog and timer resources are the same as the 64-pin body, so the extra pins buy digital headroom, not peripherals.
How much EEPROM does it carry? 2048 bytes, the same as the 128 Kbyte part, with a 300 kcycle endurance.
What is the thermal margin? 38 C/W junction to ambient for the LQFP80 at 14 by 14 mm, 443 mW of allowed dissipation at 85 C ambient, and about 57 mW of internal loss at 24 MHz from a 5 V rail.
SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the Component Obsolescence Management page walks through the checks that keep a substitute from failing on the bench.