STM8S105K6T6C
Product Specifications
STM8S105K6T6C
ST — MCU & Embedded Processors
Product Overview
The STM8S105K6T6C from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM8S105K6T6C: 32 Kbyte 5 V STM8S access line MCU in LQFP32
STM8S105K6T6C is the 32 Kbyte member of the STM8S105 access line in a LQFP32 body (7 by 7 mm), with 1 Kbyte of true data EEPROM, 2 Kbytes of RAM, 25 general purpose I/O, 23 external interrupt inputs, 8 capture compare channels, 12 high sink outputs and 7 analog inputs. The supply range is 2.95 to 5.5 V, the core runs at up to 16 MHz with zero wait state Flash access, and the converter is 10 bit with its own reference pins.
Order code and memory
| Order code | STM8S105K6T6C |
| Program Flash | 32 Kbytes |
| Data EEPROM | 1 Kbyte, 300 kcycle endurance |
| RAM | 2 Kbytes |
| Package | LQFP32, 7 by 7 mm |
| Pin count | 32 |
| Maximum general purpose I/O | 25 |
| External interrupt pins | 23 |
| Timer capture compare channels | 8 |
| ADC channels | 7 of the 10 channel converter |
| High sink outputs | 12 |
| Temperature grade | suffix 6, minus 40 to plus 85 C |
Electrical and peripheral parameters
| Supply voltage | 2.95 to 5.5 V |
| Maximum CPU clock | 16 MHz with zero wait state Flash access |
| Run current | 7.7 mA typical at 16 MHz from Flash on 5 V, 3.2 mA with the loop in RAM |
| Halt current | 6.5 uA typical at 5 V, 25 uA maximum at 85 C and 80 uA at 125 C |
| Active halt | wait, active halt and halt modes, with the auto wakeup unit |
| Low power modes | peripheral clocks can be switched off one by one |
| Wake up time | 7 microseconds from halt |
| Analog to digital converter | 10 bit, 7 channels, VREF+ and VREF- pins, 14 clock cycles per conversion |
| Digital to analog converter | not present |
| Comparators | not present on this line |
| Timers | one 16 bit advanced control timer with four capture compare channels and three complementary outputs, two 16 bit general purpose timers with five channels between them, one 8 bit basic timer, auto wakeup timer, window and independent watchdog |
| Serial interfaces | UART with LIN master, SmartCard and IrDA, SPI up to 8 Mbit/s, I2C up to 400 kHz |
| DMA | not present on this line |
| Data EEPROM endurance | 300 kcycle for the 1 Kbyte true data EEPROM |
| Program memory endurance | 10 kcycle, 20 years retention at 55 C |
| Identification | 96 bit unique ID, single wire interface module, option byte read out protection |
Points to check before this part goes on a BOM
The K6 packs the full 32 Kbyte program array and 2 Kbytes of RAM into a 7 by 7 mm 32 pin body, which makes it the smallest way to get the top of the access line. The cost is pin count and analog channels: 25 port pins, 23 external interrupt inputs, 8 capture compare channels, 7 converter channels and 12 high sink outputs. On a sensor board that is enough for a bridge, a thermistor, a supply divider and four spare channels, but a three phase measurement cannot fit.
The package still carries the advanced control timer with three complementary outputs and the break input, so a small motor drive is possible on 32 pins, with the 12 high sink outputs driving the gate drivers directly for low current bridges. What has to be checked early is the pin multiplexing: on this body several of the timer outputs share pins with the converter channels, so choosing seven analog inputs and six PWM outputs at the same time is not possible and the allocation has to be done before the first board pass.
Memory is the same as the 44 and 48 pin parts, 32 Kbytes of Flash with 1 Kbyte of true EEPROM and 2 Kbytes of RAM, and the electrical behaviour is identical: 2.95 to 5.5 V, 16 MHz, 7.7 mA typical from Flash at 5 V, 6.5 uA in halt. The trailing C on the order code belongs to the ordering string and does not change the device, so both forms should be accepted against the same line item.
Where this order code fits
Compact sensor nodes with a 5 V front end, small motor drives with low current bridges, LED drivers and any board where 32 Kbytes of code have to fit a 7 by 7 mm footprint. Teams comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and teams replacing a line that has gone end of life start from the Component Lead Time Solutions page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
How many ADC channels on the 32 pin body? Seven of the ten channels the die has, because three are not bonded on this package. The 44 pin body has nine and the 48 pin body has ten.
Can it run from 5 V? Yes, the supply range is 2.95 to 5.5 V, and the I/O ring is specified as immune to current injection, which suits industrial panels with long sensor cables.
Is the EEPROM separate from Flash? Yes, 1 Kbyte of true data EEPROM rated 300 kcycles, against 10 kcycles for the program array. Calibration and counters belong in the EEPROM.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the BOM Consolidation page sets out the checks that keep a substitute from failing on the bench.