STM8S007C8T6
Brand: ST
The STM8S007C8T6 is the flagship of the STM8S Value Line series, offering the largest memory configuration in this cost-sensitive family. With 64 KB Flash — 8× more than the S003 — it enables sophisticated firmware architectures that are impractical on smaller STM8 devices. The defining feature is the ability to implement a dual-bank Flash update mechanism: the application runs from one 32 KB bank while new firmware is written to the other, ensuring the ESC is never bricked by a failed or interrupted firmware update.
The 6 KB SRAM — 6× larger than the S003 — enables extensive runtime data logging, DShot telemetry packet assembly with large buffers, and complex commutation algorithms with generous lookup tables. The dual UART interfaces allow simultaneous connection to the flight controller (for DShot/protocol) and a debug/configuration console — a feature absent on all smaller STM8S Value Line devices which have only a single UART.
Product Specifications
STM8S007C8T6 — 64 KB Flash STM8 Value Line MCU in LQFP-48 for Drone ESC with Bootloader and Advanced BMS
The STM8S007C8T6 is the highest-end Value Line MCU from STMicroelectronics, featuring 64 KB Flash, 6 KB SRAM, and the STM8 core at 16 MHz in an LQFP-48 package. With 38 GPIOs, 10-channel 10-bit ADC, and UART/SPI/I²C interfaces, it is purpose-built for BLHeli_S ESCs with integrated bootloader (enabling field firmware updates via DShot), multi-cell BMS controllers with extensive logging, and intelligent PDBs with full per-channel telemetry. The 64 KB Flash allows a dual-bank firmware architecture with safe over-the-air updates — a critical feature for drone ESCs that must never be bricked during firmware flashing.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| STM8 | Product Family | STMicroelectronics 8-bit MCU |
| S | Product Type | Standard — mainstream (2.95–5.5V) |
| 007 | Sub-Family | Value Line High-End — 64 KB Flash, largest Value Line MCU |
| C | Pin Count | 48 pins (LQFP-48) |
| 8 | Flash Size | 64 KB |
| T | Package | LQFP |
| 6 | Temperature Range | −40°C to +85°C (industrial) |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | STM8S007C8T6 |
| Core | STM8 (8-bit, 16 MHz) |
| Flash / SRAM / EEPROM | 64 KB / 6 KB / 128 bytes |
| Package | LQFP-48 (7×7 mm, 0.5 mm pitch) |
| Supply Voltage | 2.95V – 5.5V |
| Temperature | −40°C to +85°C |
| GPIO | 38 (5V-tolerant, 20 mA sink/source) |
| ADC | 1× 10-bit, 10 channels |
| Timers | 3× 16-bit (1 advanced PWM, 2 general-purpose) |
| Communication | 2× UART, 1× SPI, 1× I²C |
| Debug | SWIM |
Product Overview
The STM8S007C8T6 is the flagship of the STM8S Value Line series, offering the largest memory configuration in this cost-sensitive family. With 64 KB Flash — 8× more than the S003 — it enables sophisticated firmware architectures that are impractical on smaller STM8 devices. The defining feature is the ability to implement a dual-bank Flash update mechanism: the application runs from one 32 KB bank while new firmware is written to the other, ensuring the ESC is never bricked by a failed or interrupted firmware update.
The 6 KB SRAM — 6× larger than the S003 — enables extensive runtime data logging, DShot telemetry packet assembly with large buffers, and complex commutation algorithms with generous lookup tables. The dual UART interfaces allow simultaneous connection to the flight controller (for DShot/protocol) and a debug/configuration console — a feature absent on all smaller STM8S Value Line devices which have only a single UART.
Key Features & Benefits
64 KB Flash — Dual-Bank Firmware for Safe Field Updates
The 64 KB Flash can be partitioned into two 32 KB banks: one running the active BLHeli_S/Bluejay firmware, the other receiving a firmware update via the DShot interface. If the update succeeds, a bank-switch flag in EEPROM activates the new firmware on next boot. If it fails, the ESC falls back to the known-good bank — eliminating brick risk during field updates, a critical safety feature for drone ESCs.
6 KB SRAM — Extensive Telemetry Buffering and Logging
With 6 KB SRAM, the S007 can maintain circular buffers of motor telemetry data spanning several seconds of flight — enabling post-flight analysis of RPM, current, temperature, and commutation timing. The large SRAM also supports advanced Bluejay features like FOC-like startup ramp generation and multi-tone startup melodies without memory pressure.
Dual UART — Simultaneous FC Communication and Debug
Unlike all smaller Value Line STM8S devices (single UART), the S007 provides two independent UARTs. One connects to the flight controller for DShot/Oneshot/Multishot protocol or telemetry streaming; the second provides a dedicated debug/configuration console or connection to an external telemetry radio (e.g., Crossfire, ELRS back-channel). No pin-sharing or time-multiplexing required.
Target Applications
Field-Updatable BLHeli_S / Bluejay ESC with Bootloader
The dual-bank Flash architecture enables safe over-the-wire firmware updates via the DShot signal line — no external programmer needed. ESC firmware can be updated in-field through Betaflight passthrough or BLHeliSuite without risk of bricking, making it ideal for commercial drone platforms where ESC accessibility is limited.
Advanced Drone BMS with Flight Data Logging
The 6 KB SRAM buffers minutes of battery telemetry (cell voltages, current, temperature, SOC) for post-flight analysis. The dual UARTs connect to both the flight controller and an external display/logging device. The 64 KB Flash stores calibration tables, cycle history, and safety threshold profiles for multiple battery chemistries (LiPo, Li-Ion, LiHV).
DroneCAN / UAVCAN ESC Node Controller
With the larger Flash and dual UARTs, the S007 can implement a DroneCAN/UAVCAN ESC node with full CAN protocol via a UART-to-CAN bridge (e.g., MCP2515 + MCP2551). The extra Flash accommodates the CANopen stack, ESC status reporting, and field-update capability required by DroneCAN specification.
Frequently Asked Questions
Does the STM8S007 offer CAN bus natively?
No — the STM8S007 Value Line does not include a CAN peripheral. For native CAN 2.0B support on STM8, you must use the STM8S207/STM8S208 Performance Line or STM8AF52 Automotive Line, which include an on-chip beCAN (Basic Enhanced CAN) controller. The S007 can implement CAN via an external SPI-to-CAN bridge (MCP2515), but this adds BOM cost and PCB area. If CAN is required in your ESC or BMS design, consider the STM8S207CBT6 instead.
Can Bluejay/AM32 firmware use the STM8S007's 64 KB Flash?
Yes. AM32 (an open-source 32-bit ESC firmware) does not target STM8, but Bluejay and custom BLHeli_S forks can utilize the full 64 KB Flash for dual-bank operation. The standard Bluejay binary (~16–20 KB) occupies only one-third of the S007's Flash, leaving ample room for a second firmware bank, extended telemetry, or a bootloader partition. However, the standard Bluejay project does not yet include automated dual-bank update logic — this would require custom firmware development.
Ordering Information
| Orderable Part Number | Package | Packaging | Temperature |
|---|---|---|---|
| STM8S007C8T6 | LQFP-48 (7×7 mm, 0.5 mm pitch) | Tray | −40°C to +85°C |
Design Resources
Datasheet: STM8S007C8 — Value Line high-density datasheet with LQFP-48 pinout and electrical characteristics.
Reference Manual (RM0016): STM8S Series — Full register-level documentation.
Bluejay GitHub:
mathiasvr/bluejay— Open-source BLHeli_S alternative with STM8S target support.STVD + COSMIC: Free IDE for custom bootloader and dual-bank firmware development.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics STM8S007C8T6 MCUs with full traceability and batch-level QA documentation. With 64 KB Flash, 6 KB SRAM, and dual UARTs, the STM8S007C8T6 is the ultimate Value Line STM8 — enabling safe dual-bank firmware updates and extensive telemetry buffering for professional drone ESC and BMS applications. Whether you need prototype quantities for ESC firmware development or production volumes for drone BMS and PDB controller manufacturing, we source through verified channels with competitive lead times. Contact us with your target quantity, delivery date, and any special packaging or marking requirements — we'll respond with a detailed quotation within 24 hours.