STM8L152C6T6
Product Specifications
STM8L152C6T6
ST — MCU & Embedded Processors
Product Overview
The STM8L152C6T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM8L152C6T6: 32 Kbyte ultra-low-power STM8L MCU in LQFP48
STM8L152C6T6 is a 32 Kbyte Flash member of the STM8L ultra-low-power line in a LQFP48 body (7 by 7 mm), with 2 Kbytes of RAM, 1 Kbyte of data EEPROM, 41 general purpose I/O, 25 channels on the 12 bit converter and 1 channel of 12 bit DAC. The supply range is 1.8 to 3.6 V, down to 1.65 V at power down and the core runs at up to 16 MHz. It also carries a segment LCD controller driving 4x28 segments with step up converter.
Order code and memory
| Order code | STM8L152C6T6 |
| Program Flash | 32 Kbytes |
| Data EEPROM | 1 Kbyte with ECC and read while write |
| RAM | 2 Kbytes |
| Package | LQFP48, 7 by 7 mm |
| Pin count | 48 |
| Maximum general purpose I/O | 41 |
| ADC channels | 25 of the 12 bit converter |
| DAC channels | 1 of 12 bits with output buffer |
| LCD controller | 4x28 segments with step up converter |
| Temperature grade | suffix 6, minus 40 to plus 85 C |
Electrical and peripheral parameters
| Supply voltage | 1.8 to 3.6 V, down to 1.65 V at power down |
| Maximum CPU clock | 16 MHz, 16 MIPS peak |
| Run current | 195 uA per MHz plus 440 uA static |
| Halt current | 350 nA typical |
| Active halt | 1.3 uA typical with the real time clock running |
| Low power modes | 5.1 uA typical in low power run, 3 uA in low power wait |
| Wake up time | 4.7 microseconds from halt |
| Analog to digital converter | 12 bit, up to 1 Msps, 25 channels, internal reference voltage and temperature sensor on chip |
| Digital to analog converter | 1 channel of 12 bits with output buffer, 7 microseconds typical settling into 5 k and 50 pF |
| Comparators | 2, one fixed threshold and one rail to rail, both can wake the core |
| Timers | two 16 bit general purpose timers with two channels each, one 16 bit advanced control timer with three channels, one 8 bit timer, beeper timer, window and independent watchdog |
| Serial interfaces | one SPI, one I2C at 400 kHz with SMBus and PMBus, one USART with ISO 7816 and IrDA |
| DMA | 4 channels covering the ADC, the DAC, SPI, I2C, USART and the timers |
| Data EEPROM endurance | 300 kcycle with ECC and read while write |
| Program memory endurance | 10 kcycle, 30 years retention at 85 C |
| Identification | 96 bit unique ID, single wire interface module, USART bootloader |
Points to check before this part goes on a BOM
The C6 is the 32 Kbyte, 48 pin member with the LCD controller, and it is the order code that shows up most in metering BOMs because it balances three budgets at once: enough program space for a protocol stack and a display menu, 41 port pins for keys and segment outputs, and a halt current that keeps a lithium cell alive for a decade. The converter keeps all 25 channels on this body, so a three phase measurement plus temperature and battery sensing fits without multiplexing tricks.
The display driver on this family is not a simple GPIO expander. It has its own bias generation with a step up converter, programmable frame frequency, and it can be configured for static, 1/2, 1/3 or 1/4 duty, which changes both the segment count and the contrast behaviour as the supply falls. When the glass is specified early, the duty and bias choice fixes how many pins the display takes and therefore how many remain for the ADC, so the glass datasheet belongs in the pin planning meeting and not in the enclosure review.
Two 16 bit general purpose timers, one advanced control timer with three channels and complementary outputs, an 8 bit timer and a beeper timer cover most panel work, and the four channel DMA can move ADC results without waking the core. On the current side, 195 uA per MHz plus 440 uA static in run mode, 5.1 uA in low power run, and 350 nA in halt give a wide range to work with; the mistake to avoid is leaving the display bias converter running from a rail that also feeds the ADC reference.
Where this order code fits
Electricity and water meters, HVAC wall controllers, medical panel meters and industrial displays that combine a segment glass with a 12 bit measurement front end. Teams comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and teams replacing a line that has gone end of life start from the Incoming Inspection Plan page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
How much Flash does a display product usually need? Metering firmware with a display menu, a protocol and a calibration table typically lands between 20 and 28 Kbytes on this core, which is why the 32 Kbyte C6 is the common choice and the 16 Kbyte C4 is reserved for simpler panels.
Is the segment driver usable with a multiplexed glass? Yes. Duty ratios from static up to 1/4 are supported with the internal step up converter, and the segment count depends on the duty chosen, so the glass datasheet decides the pin budget.
What temperature grades exist? Suffix 6 is minus 40 to plus 85 C and suffix 3 is minus 40 to plus 125 C. Metering products that sit outdoors usually need the 3 suffix, which has to be ordered explicitly.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.