Contact Us

STM8L101F3P6

Brand: ST
ST STM8L101F3P6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM8L101F3P6 — MCU & Embedded Processors | Superb Automation

STM8L101F3P6

ST — MCU & Embedded Processors

Product Overview

The STM8L101F3P6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM8L101F3P6: 8 Kbyte ultra-low-power STM8L101 MCU in TSSOP20

STM8L101F3P6 is an 8 bit ultra-low-power part in a TSSOP20 body (4.4 by 6.4 mm) with 8 Kbytes of Flash, up to 2 Kbytes of that array usable as data EEPROM, 1.5 Kbytes of RAM and 16 port pins. The core runs at up to 16 MHz from a 1.65 to 3.6 V supply, there is no analog to digital converter, and the analog work is carried by two comparators with four inputs each. Halt current is 0.3 uA and active halt 0.8 uA, which is the lowest sleep current in the STM8L family.

Order code and memory

Order codeSTM8L101F3P6
Program Flash8 Kbytes, shared with the data area
Data EEPROMup to 2 Kbytes taken from the same array
RAM1.5 Kbytes
PackageTSSOP20, 4.4 by 6.4 mm
Pin count20
Maximum general purpose I/O16
Analog to digital converternot present
Comparators2 with 4 inputs each
Temperature gradesuffix 3, minus 40 to plus 125 C

Electrical and peripheral parameters

Supply voltage1.65 to 3.6 V
Maximum CPU clock16 MHz, 16 MIPS peak
Run currentabout 150 uA per MHz
Halt current0.3 uA typical
Active halt0.8 uA typical with the auto wakeup unit running
Low power modesthree low power modes, wait, active halt and halt
Wake up timeabout 4 microseconds from the internal 16 MHz RC start up
Analog to digital converternot present
Digital to analog converternot present
Comparators2, each with four inputs and a shared reference, both can wake the core
Timerstwo 16 bit general purpose timers with two channels each, one 8 bit timer, beeper timer, auto wakeup unit, independent watchdog
Serial interfacesSPI, I2C, USART
DMAnot present on this line
Data EEPROM enduranceup to 2 Kbytes taken from the Flash array, 300 kcycle
Program memory endurance20 years retention at 55 C
Identification96 bit unique ID, single wire interface module, in circuit emulation

Points to check before this part goes on a BOM

The F3 is the smallest member of the ultra-low-power line: a 20 pin TSSOP body with 8 Kbytes of Flash, of which up to 2 Kbytes can be allocated as data EEPROM, and 1.5 Kbytes of RAM. There is no analog to digital converter on this part, only two comparators with four inputs each, so a product that needs to measure a voltage has to do it by comparing against a threshold or by timing an RC network. That single omission is what separates the L101 line from the L151 parts and it decides the application before any other figure is considered.

Sixteen port pins remain on the 20 pin body after the supply, ground and reset pins are counted, and one of those is the reset pin which can serve as PA1 when the reset function is disabled. The pin budget therefore suits a keypad of four keys, two LEDs, a buzzer, a serial link and a comparator input, and not much more. The package is 4.4 by 6.4 mm, which is the reason this order code appears in products where the board is the size of a coin.

Power is the headline: 0.3 uA in halt, 0.8 uA in active halt with the auto wakeup unit running, and about 150 uA per MHz in run mode, from a supply that works down to 1.65 V. The 8 Kbyte array shares its space with the EEPROM, so the split between code and data is a firmware decision made at link time rather than a hardware choice, and a product that logs 2 Kbytes of records has only 6 Kbytes left for code.

Where this order code fits

Coin cell sensors, remote key fobs, battery tags, simple timers and any 20 pin control head where a comparator threshold is enough and a 12 bit measurement is not needed. Teams comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and teams replacing a line that has gone end of life start from the How to Reduce Component Cost page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Does this part have an ADC? No. The STM8L101 line has two comparators with four inputs each instead of a converter, so measurement is done against a threshold or by timing. The L151 and L152 lines carry the 12 bit converter.

How much of the 8 Kbytes can be EEPROM? Up to 2 Kbytes, taken from the same array, so the code space drops to 6 Kbytes when the full data area is reserved. The EEPROM is rated 300 kcycles.

What temperature range does the P6 suffix give? Suffix 3 is minus 40 to plus 125 C. The F3 device is specified for both the 85 C and the 125 C grade, and the suffix on the order code is what fixes it.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.