STM32F205ZGT6
Product Specifications
STM32F205ZGT6
ST — MCU & Embedded Processors
Product Overview
The STM32F205ZGT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32F205ZGT6: 1 Mbyte and 114 I/Os at 120 MHz
STM32F205ZGT6 is the 1 Mbyte, 144 pin member of the STM32F205 line: 128 Kbytes of system SRAM plus 4 Kbytes of backup, 114 I/O pins, 24 analog channels from three converters, the flexible static memory controller with the LCD parallel interface, fifteen communication interfaces and a 120 MHz Cortex-M3 with the adaptive real time accelerator. It is the density where memory, pins and speed are all at the top of the family at the same time, and the natural choice for a controller that runs a graphical interface and a real time control loop on one device.
What 144 pins and 1 Mbyte together allow
An external SRAM or a parallel display on the memory controller takes about 25 pins, the three converters take their channels from ports A and C, and the two CAN buses, three USARTs, the USB ports and the SDIO card take their own. Even after all of that there are enough pins left for a keypad, encoder inputs and a bank of digital outputs, which is the configuration of a mid range industrial panel. The 120 MHz core with the accelerator is what makes a refresh loop and a control loop coexist without one starving the other.
Values at a glance
| Parameter | Value | Note |
|---|---|---|
| Core and clock | Cortex-M3, 120 MHz, 150 DMIPS | Accelerator, MPU, 17 timers |
| Flash, SRAM | 1 Mbyte, 128 plus 4 Kbytes | 512 bytes of one time programmable memory |
| Package | LQFP144, 20 by 20 mm | LQFP64, LQFP100, LQFP176 and UFBGA176 bodies also exist in the family |
| I/O | 114 pins | Fast I/O up to 60 MHz, most 5 V tolerant |
| ADC, DAC | 3 converters, 12 bit, 24 channels; 2 DAC channels | 2 MSPS each, 6 MSPS triple interleaved |
| External memory | FSMC, LCD interface in 8080 and 6800 modes | NOR, PSRAM, SRAM, NAND and Compact Flash |
| Communication | 3 I2C, 3 SPI, 2 I2S, 4 USART, 2 UART, 2 CAN, SDIO, 2 USB OTG | Fifteen interfaces, SPI at 30 Mbit/s |
| Supply | 1.8 to 3.6 V | Backup domain supplied separately through VBAT |
17 timers is a scheduling resource
Ten general purpose 16 bit timers, two advanced control timers with dead time and break inputs, two basic timers, two watchdogs and the SysTick counter make up the seventeen. In a controller with several PWM channels, an encoder input, a periodic control interrupt and a time base for the display, the timer count stops being a specification detail and becomes the reason the part is chosen. Running out of timers means bit banging a waveform in software, which is exactly where a 120 MHz core ends up spending its headroom.
Platform sourcing for a high pin count part
The ZG density is the most specified code in the F205 line for panel controllers, so stock tends to exist but availability moves between the G and the F densities, which differ only in flash size. Because the body and the SRAM are the same, the swap needs a firmware rebuild and nothing else. An alternate part record, a strategic sourcing plan for the annual volume, and an medical device component review where the product carries a clinical marking are the three documents that a platform decision usually requires.
Common questions
Is the LCD interface a full display controller? No. It is a bus interface in 8080 or 6800 mode with the timing generated by the application, so the refresh cost stays with the firmware.
Can both USB ports be used at once? Yes, one high speed through the external ULPI PHY and one full speed with the on chip PHY, and they share the 16 Kbyte SRAM block for DMA access.
What happens to the backup SRAM if VBAT is missing? It loses its contents, and the RTC stops. A board that relies on the retained block has to provide the coin cell or a supercapacitor on the VBAT pin, which is a separate decision from the main supply.