Contact Us

STM32F105VBT6

Brand: ST
ST STM32F105VBT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F105VBT6 — MCU & Embedded Processors | Superb Automation

STM32F105VBT6

ST — MCU & Embedded Processors

Product Overview

The STM32F105VBT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F105VBT6: 128 Kbytes, Two CAN Buses and USB OTG in LQFP100

STM32F105VBT6 is the quad flat 100 pin version of the connectivity line at 128 Kbytes of flash and 64 Kbytes of SRAM. It is the part chosen when a product has to sit between two CAN networks and a USB host at the same time, and it is the part that gets compared with the STM32F107VB when someone discovers that Ethernet was wanted after all. Both carry the same two CAN controllers, the same OTG controller and the same 72 MHz core; Ethernet is the one hardware difference in the family.

Ten timers and a 12 channel DMA

Four general purpose 16 bit timers with quadrature encoder inputs, one motor control timer with dead time and emergency stop, two basic timers to drive the DAC, two watchdogs and the SysTick counter. The twelve channel DMA is what makes the two CAN interfaces usable at high bus load, because message copies run without the core, and the same channels serve the SPI, I2S and USART peripherals. Timer pins on this line are remappable, which helps when the CAN, USB and I2S pin assignments collide on a 100 pin body.

Values at a glance

ParameterValueNote
Core and clockCortex-M3, 72 MHz1.25 DMIPS/MHz, trace macrocell
Flash, SRAM128 Kbytes, 64 Kbytes64 Kbyte and 256 Kbyte codes exist in the same body
PackageLQFP100, 14 by 14 mmLFBGA100 body available
I/O80 pinsUp to 80 fast I/Os, almost all 5 V tolerant
CAN2 controllers, 2.0B active512 bytes of dedicated SRAM for the pair
USB2.0 full speed device, host, OTGOn chip PHY, HNP, SRP and ID pin support
Analog2 ADC 12 bit 16 channels; 2 DAC2 MSPS interleaved, conversion range 0 to 3.6 V
Clock sourceCrystal 3 to 25 MHzInternal 8 MHz RC and 40 kHz RC also available

Two buses means two transceivers and two grounds

A gateway between two CAN networks needs two transceivers, and if the two buses belong to different pieces of equipment they usually arrive on different connectors with different ground references. The 2.0B controllers handle the protocol, but the isolation decision belongs to the board: a shared ground with a common mode choke is enough inside one cabinet, while two separate chassis need galvanic isolation on at least one port. That choice sets the transceiver part number and the board area before the firmware is written, and it is the most common reason a gateway board goes through a second revision.

Supply and the Ethernet question

If the product may need Ethernet within two years, the F107 code is the same footprint with the MAC included, and the cost difference at the part level is smaller than the cost of a board revision. Where the F105 code is the right answer and stock is thin, the options are the neighbouring densities in the same body or the F107 code used without the Ethernet. A microcontroller cross reference sheet, a CAN transceiver selection note for the isolated and non isolated cases, and an OEM procurement plan that covers both network ports are the groundwork for that decision.

Common questions

How does this differ from the STM32F103VBT6? Same package and flash size, but the F105 has two CAN controllers, a USB OTG port with host support, two DAC channels, a 12 channel DMA and a wider crystal range. The F103 has one CAN and a device only USB port.

Can the OTG port power a USB stick? The controller handles the protocol, but the 5 V port supply has to be switched externally, and the current limit belongs to that switch rather than to the microcontroller.

Is the USB clock the same as the core clock? The USB needs 48 MHz, produced from the PLL with the crystal as the reference, and the internal RC is not accurate enough for reliable operation.