STM32F103ZEH6
Product Specifications
STM32F103ZEH6
ST — MCU & Embedded Processors
Product Overview
The STM32F103ZEH6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32F103ZEH6: 112 I/Os and 512 Kbytes in a 10 mm LFBGA144
STM32F103ZEH6 is the 144 pin high density device in the LFBGA144 body, which measures 10 by 10 mm against the 20 by 20 mm of the quad flat package of the same pin count. Flash is 512 Kbytes, SRAM is 64 Kbytes, and the pin count exposes ports A to G for 112 usable I/Os, the full flexible static memory controller and the LCD parallel interface. The H in the code marks the ball grid package and the 6 marks the minus 40 to plus 85 C industrial range.
What 144 pins add over the 100 pin body
Port F and port G arrive, which is where the upper address and data lines of the memory controller and the external interrupt lines beyond 16 live. The memory controller gains its full set of chip selects, so a board can carry a NOR flash, an SRAM and a NAND device at the same time. For a board that drives a graphical display from an external frame buffer, this is the density where the bus has enough lines to do it without multiplexing tricks, and 112 I/Os leaves room for the rest of the machine.
Values at a glance
| Parameter | Value | Note |
|---|---|---|
| Core and clock | Cortex-M3, 72 MHz | 1.25 DMIPS/MHz, hardware divide |
| Flash, SRAM | 512 Kbytes, 64 Kbytes | 256 and 384 Kbyte codes in the same package |
| Package | LFBGA144, 10 by 10 mm | LQFP144 is 20 by 20 mm at the same pin count |
| I/O | 112 pins | Almost all 5 V tolerant, 16 external interrupt vectors |
| ADC, DAC | 3 converters, 12 bit, 21 channels; 2 DAC channels | 21 channels is the largest analog count in the family |
| External memory | FSMC with four chip selects | NOR, PSRAM, NAND, Compact Flash style |
| Communication | 3 SPI, 2 I2S, 2 I2C, 5 USART, SDIO, USB, CAN | Thirteen interfaces, LCD interface in 8080 and 6800 modes |
| Temperature | Minus 40 to plus 85 C | Junction limit 125 C, suffix 7 gives 105 C ambient |
The board cost of a 10 mm 144 ball array
A 0.8 mm pitch ball grid with 144 balls on 10 mm needs at least a four layer board to route the memory bus out, and probably six layers to keep the display and analog sections quiet. That is the trade against the quad flat part, which routes on four layers with wider traces and can be reworked by hand. Volume production usually takes the ball grid for the smaller area, while prototypes and low volume instrumentation stay on the quad flat body. Both bodies are electrically the same die, so firmware written for one runs on the other.
Sourcing a 144 pin ball grid part
Stock of the ball grid bodies is thinner than the quad flat equivalents across the whole STM32F103 range, and the ZE code is one of the more heavily used densities, so lead times move quickly. A build that can accept the quad flat ZE code gains access to a much larger pool of reels, at the cost of board area. Confirming that the two bodies are the same device is a microcontroller cross reference question, and the procurement answer usually involves a component obsolescence review of the family and an incoming inspection plan for the ball grid parts, where coplanarity and moisture sensitivity cannot be checked by eye.
Common questions
Why does this body have 21 analog channels when the 100 pin part has 16? The extra pins on ports F and G free analog inputs that are shared with digital functions on the smaller bodies. The converters themselves are identical.
Can the same firmware image be used on the LQFP144 part? Yes, same die and same memory map. Only the package outline and the programming fixture differ.
Is the LCD interface a display controller? No. It is a parallel bus interface in 8080 or 6800 mode, so the application has to generate timing and refresh the panel itself.