STM32F103VFT6
Product Specifications
STM32F103VFT6
ST — MCU & Embedded Processors
Product Overview
The STM32F103VFT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32F103VFT6: 768 Kbytes, Dual Bank Flash and an MPU in 100 Pins
STM32F103VFT6 belongs to the XL density line, the largest of the STM32F103 variants: 768 Kbytes of flash arranged in two banks, 96 Kbytes of SRAM, a memory protection unit, a trace macrocell, seventeen timers and a flexible static memory controller, in the same 100 pin LQFP body used by the smaller high density parts. The F in the code is the 768 Kbyte density and the G code is 1 Mbyte. Core frequency is still 72 MHz, so the extra memory is there for code size and for in application programming rather than for compute.
What the second flash bank buys
The first bank is 512 Kbytes and the second is 256 Kbytes on this density. Two banks means code can execute from one while the other is erased and rewritten, which is what a field update needs if the product has no external memory and cannot afford a bootloader that stops the application for the whole transfer. The application writes the new image into the idle bank, verifies it, and switches the boot address. The catch is that the two banks are not one flat region, so the linker script and the vector table relocation have to be written for the arrangement from the start rather than bolted on at the end of a project.
Values at a glance
| Parameter | Value | Note |
|---|---|---|
| Core and clock | Cortex-M3 with MPU, 72 MHz | Embedded trace macrocell included on this line |
| Flash, SRAM | 768 Kbytes in two banks, 96 Kbytes | Bank one 512 Kbytes, bank two 256 Kbytes |
| Package | LQFP100, 14 by 14 mm | LQFP144 and LFBGA144 bodies carry the same density |
| I/O | 80 pins | Almost all 5 V tolerant |
| ADC, DAC | 3 converters, 12 bit, 16 channels; 2 DAC channels | Dual sample and hold, 1 microsecond conversion |
| Timers | 10 general purpose plus 2 motor control plus 2 watchdog | Seventeen timers counted by the vendor |
| Communication | 3 SPI, 2 I2S, 2 I2C, 5 USART, SDIO, USB, CAN | LCD parallel interface in 8080 and 6800 modes |
| Temperature | Minus 40 to plus 85 C | Code 7 reaches 105 C ambient, junction limit 125 C |
96 Kbytes of SRAM changes what is possible
At 96 Kbytes the frame buffer question comes back into range: a 320 by 240 pixel display at 8 bits per pixel is 76.8 Kbytes, which fits with about 19 Kbytes left for the application, or a 240 by 320 monochrome buffer fits several times over. Audio buffers, a Modbus register map with logging and a TCP stack on an external PHY are all realistic on this density. The memory map has 96 Kbytes contiguous, so a single large buffer does not have to be split the way it is on the smaller parts.
Supply and the XL density codes
The VF and VG codes are the two XL densities in the 100 pin body, and the only difference is 768 Kbytes against 1 Mbyte. Since both use the same die arrangement, a build that cannot get the VF code can often take the VG code without a board change, subject to the firmware size review. Where neither is available, the practical fallbacks are the high density VE code with a firmware diet, or an open market purchase with the documentation that goes with it. The supporting steps are a microcontroller cross reference across the three densities, a strategic sourcing review of how much of the annual volume to commit, and a BOM consolidation pass that stops two densities of the same device being bought on separate lines.
Common questions
Does the MPU slow the core down? No. It adds a permission check per access region and is transparent when the regions are configured to allow the access, but it does add a fault path that the firmware has to handle rather than ignore.
Can both flash banks be read at once? The two banks are on the same flash interface with separate control, so code runs from one bank while the other is programmed, and read access to the bank being erased is not possible.
Is the part a drop in for the high density VE code? Same package and the same pin functions, but the flash organisation and the available SRAM differ, so the linker script and the programming algorithm both change. The board does not.