Contact Us

STM32F103VDT6

Brand: ST
ST STM32F103VDT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F103VDT6 — MCU & Embedded Processors | Superb Automation

STM32F103VDT6

ST — MCU & Embedded Processors

Product Overview

The STM32F103VDT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F103VDT6: 100 Pins, 80 I/Os, 384 Kbytes of High Density Flash

STM32F103VDT6 is the 100 pin LQFP body of the STM32F103 high density line at 384 Kbytes of flash and 64 Kbytes of SRAM. The step from the 64 pin RD part to this one is 29 extra I/O pins and the full flexible static memory controller, which on the 100 pin body can drive an external SRAM or a multiplexed display bus instead of the narrow latch interface that the 64 pin version is limited to. Core speed stays at 72 MHz and the supply stays at 2.0 to 3.6 V.

Pin budget on a 100 pin body

Eighty usable I/Os across ports A to E, with 16 analog channels from the three converters and the two DAC channels on port A. A parallel 16 bit bus for an external memory or a TFT takes around 25 of those pins including chip selects, which leaves about 55 for everything else: a CAN transceiver pair, a USB connector, three USARTs to a modem or a host, an SD card in SDIO mode and a keypad. That is a realistic configuration for an instrument front panel, and it is the reason this density sits in so many industrial products.

Values at a glance

ParameterValueNote
Core and clockCortex-M3, 72 MHzSingle cycle multiply, hardware divide, 1.25 DMIPS/MHz
Flash, SRAM384 Kbytes, 64 Kbytes256 Kbyte VC and 512 Kbyte VE codes in the same body
PackageLQFP100, 14 by 14 mmLFBGA100 is the ball grid alternative
I/O80 pins5 V tolerant on the digital pins
ADC, DAC3 converters, 12 bit, 16 channels; 2 DAC channels1 microsecond conversion, dual sample and hold
External memoryFSMC Bank1 and Bank2Multiplexed NOR, PSRAM and NAND support
Communication3 SPI, 2 I2S, 2 I2C, 5 USART, SDIO, USB, CANThirteen interfaces, five of them USARTs
TemperatureMinus 40 to plus 85 CSuffix 7 covers minus 40 to plus 105 C

Flash wait states at 72 MHz

The high density devices run the core at 72 MHz from a 3.3 V rail with two flash wait states, and the prefetch buffer with the instruction and data caches keeps the average near one cycle per instruction for straight line code. Tight loops that jump across the 1 Kbyte cache boundaries lose some of that benefit, and the timing consequence shows up first in bit bang protocols and in interrupt latency measurements. Code placed in SRAM removes the wait states entirely, which is why a 64 Kbyte SRAM part can run a time critical section from RAM while the rest runs from flash.

Supply continuity for a 100 pin high density part

The VC, VD and VE codes differ only in flash size, so a build that is short of the VD part can often be covered by the VE part with no board change and only a firmware size review. Where the exact code is contractually fixed, the question becomes one of channel: the open market holds the VD code more often than the franchise channel does, and the difference is documentation rather than silicon. A microcontroller cross reference table, a component obsolescence plan for the family, and a BOM consolidation review that keeps density variants on one line are the three steps that keep such a build moving.

Common questions

Is the 100 pin part pin compatible with the 144 pin part? No. The 144 pin body adds port F and port G plus the full FSMC, and the package footprint changes from 14 by 14 mm to 20 by 20 mm.

How many USARTs can run at once? Five, of which three are USART and two are UART. All five share the two APB buses, and the baud rate accuracy depends on the clock tree configuration for each one.

Can the FSMC drive a TFT directly? Yes, in multiplexed mode with an address latch, which is the common arrangement for a 16 bit display bus. The refresh has to be handled by the application because the controller has no display engine.