VBL165R20S
Product Specifications
VBL165R20S
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL165R20S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL165R20S: 650 V and 20 A at 160 milliohm
The VBL165R20S is a single N channel MOSFET in a TO263 body rated at 650 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 20 A of drain current and 160 milliohm at a 10 V gate. The technology is SJ_Multi-EPI, a superjunction process, which is what makes 160 milliohms possible at this voltage in this body.
Six hundred and fifty volts is the standard for an offline converter on a rectified 220 V main, and it also covers a 400 V DC bus. The superjunction die brings the resistance down to a level where 10 A is a realistic current, which a planar die at the same voltage cannot do.
At 160 milliohm the loss at 2 A is 0.64 W, at 10 A it is 16 W and at the printed 20 A it is 64 W. The first is comfortable in a TO263, the second needs a heavy pad and the third is beyond a surface mount joint.
Key data for the VBL165R20S
| Configuration | Single N channel |
| Package | TO263, surface mount, tab soldered to the board |
| VDS | 650 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V typical |
| ID | 20 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 160 milliohm |
| Technology | Superjunction, multiple epitaxy |
| Loss at 2 A | 0.64 W at 160 milliohm |
| Loss at 10 A | 16 W at 160 milliohm |
| Gate window | Plus or minus 30 V |
| Thermal path | Tab to copper, no isolated substrate |
Superjunction behaviour in a flyback
A superjunction die switches fast and has a low output capacitance at high drain voltage, which is what makes a 65 to 150 kHz offline converter practical in this body. The capacitance is non linear, so the charge removed at turn on is concentrated near zero volts and the driver current is not the same as a linear capacitance of the same nominal value would imply.
The body diode is fast and recovers hard. In a flyback that does not matter, because the diode never conducts in normal operation. In a bridge or an active clamp it does, and the recovery rings against the loop inductance and the transformer capacitance.
The safe operating area is narrower than a planar die of the same voltage. A clamp that keeps the drain below 520 V also keeps the part out of avalanche, which is where this process wants to be. Where the clamp is marginal the planar part in this band at 4500 milliohm is the more forgiving choice, at the cost of current.
Sixteen watts at ten amps in a surface mount body
At 160 milliohm and 10 A the loss is 16 W. A TO263 tab on a large pad with vias into an inner plane removes that with an acceptable rise, and on a pad the size of the tab it does not. The difference between the two is the reason boards with the same part run at different temperatures.
At 5 A the loss is 4 W and the part is comfortable on an ordinary pad. Most offline converters at 150 to 300 W draw between 0.8 and 1.6 A from the 310 V bus on average, so the conduction loss in a continuous mode circuit is under 0.5 W and the switching loss is the larger term.
That changes the optimisation. For a continuous mode flyback the gate charge and the output capacitance matter more than the resistance, and neither is printed on this page. Ask for both curves before the frequency is fixed.
A 310 V rail with a high line tolerance of 15 per cent is 356 V. The derated ceiling at 80 per cent of 650 V is 520 V, which leaves 164 V for the leakage spike. A flyback with a well coupled transformer produces 80 to 120 V of spike, so the margin is real.
An active clamp reset recycles the leakage energy instead of dissipating it, and it also reduces the drain spike. That topology suits a superjunction die well, because the clamp keeps the drain inside the derated ceiling on every cycle and the low capacitance gives a fast transition.
Creepage on the tab matters at 650 V. The tab is at drain potential, the leads are a millimetre apart and the part sits on a board that also carries the mains. A slot, a conformal coat or a coated board are the standard measures at pollution degree 2.
Where the part fits and where it does not
It fits the primary switch of an offline flyback from about 30 to 150 W, an active clamp forward on a 400 V bus, a power factor correction stage at low power, a discharge switch and an inverter leg on a 400 V DC bus. It does not fit a position where avalanche energy is expected on every cycle.
For an offline converter the deciding parameters are the leakage spike the clamp leaves and the capacitance the driver has to charge. Our medical device components page covers how the primary side parts are specified for a product with a long service life and a tight reliability requirement.
The sourcing side of this part is covered on the supplier corrective action. For a part in a product with a long service life, that page covers how a field return is closed out at the source.
Questions we get on this code
Is 160 milliohm real at 650 V? For a superjunction die, yes. A planar die at this voltage sits nearer 4500 milliohms, which is the part below this one in the band.
Is 20 A usable? At 64 W of loss, no. At 5 to 10 A the part works with a good pad, and the practical continuous figure is nearer 8 to 10 A.
Does it need a snubber? In a flyback the clamp does the job. In a bridge the body diode recovery needs a snubber or a slow turn on of the opposite switch.
What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.