VBL1602
Product Specifications
VBL1602
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL1602 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL1602: 60 V and 270 A at 3 milliohm
The VBL1602 is a single N channel MOSFET in a TO263 body rated at 60 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 270 A of drain current, 7 milliohm at a 4.5 V gate and 3 milliohm at a 10 V gate. The gap between the two columns is more than a factor of two.
Sixty volts is the class for a 48 V system at the top of charge, which is about 58 V, and for a 42 V automotive rail. At the 80 per cent rule the part works to 48 V, so a 48 V pack at 58 V is inside the absolute rating and outside the derated ceiling, which means it works with a clamp and not without one.
At 3 milliohm the loss at 80 A is 19.2 W and at the printed 270 A it is 218.7 W. The second figure is not a board number. Even the first needs a heavy copper pad, which is the shape of every high current part in this band.
Key data for the VBL1602
| Configuration | Single N channel |
| Package | TO263, surface mount, tab soldered to the board |
| VDS | 60 V |
| VGS | Plus or minus 20 V |
| Vth | 3 V typical |
| ID | 270 A, a die figure at a 25 C case |
| RDS(on) at 4.5 V | 7 milliohm |
| RDS(on) at 10 V | 3 milliohm |
| Technology | Trench |
| Loss at 20 A | 1.2 W at 3 milliohm, 2.8 W at 7 milliohm |
| Loss at 80 A | 19.2 W at 3 milliohm |
| Thermal path | Tab to copper, no isolated substrate |
Two point three times the loss at half the gate drive
Seven milliohms at 4.5 V against 3 at 10 V is a ratio of 2.3, and on a loss budget that ratio is the difference between a pad and a heatsink. At 80 A the 3 milliohm figure gives 19.2 W and the 7 milliohm figure gives 44.8 W, which no TO263 removes without a real heatsink.
The lesson is that the gate drive is part of the part specification. A board that quotes the 10 V column and then drives from a 5 V rail is out by a factor of 2.3 on every loss figure, and the error only shows up when the board runs hot.
The 3 V threshold means a 5 V driver has 2 V of overdrive, which is enough to conduct but not enough to reach 3 milliohm. With a 12 V housekeeping rail and a 10 V gate drive, the 3 milliohm column applies and the circuit behaves as intended.
Sixty volts and the transient that comes with a battery
A 48 V pack at 58 V is 2 V below the absolute rating. A disconnect that opens under load, or a fuse that clears a fault, puts the pack and cable inductance into the drain node and the peak passes 58 V for tens of nanoseconds. At 60 V there is almost no room.
The clamp is the answer, and it has to be close to the switch to keep the loop small. A suppressor that clamps at 55 V leaves the drain 5 V below absolute and 7 V above the derated ceiling, which is the working compromise for this class.
The other contributor is the body diode recovery. At 270 A the recovery charge is large, and in a synchronous rectifier that charge is a loss and a ringing source. Where the part is used as a rectifier, a snubber or a slower turn on of the opposite switch reduces it.
A TO263 has one tab, about 10 mm by 9 mm, and three leads. The die can pass 270 A at a 25 C case, but the joint and the copper cannot pass 270 A without enormous loss. At 3 milliohm, 270 A is 218.7 W, which would destroy the joint long before the die.
The working continuous current is where the loss matches what the copper removes. For a two ounce board with a large pad and vias into an inner plane, that is around 50 to 70 A. Above that the part needs a heatsink or a different package.
Where the load is a pulse, the die mass carries the first tens of milliseconds and the average loss decides the temperature. A motor start at 200 A for a few milliseconds is easy. A continuous 200 A is not a surface mount question.
Where the part fits and where it does not
It fits a battery disconnect on a 48 V pack, an inverter stage on a 48 V motor drive, a synchronous rectifier in a 48 V to 12 V converter, an ORing switch on a 48 V bus and a large load switch. It does not fit a 96 V pack, and it does not fit a continuous load above about 70 A in this body.
For a 48 V pack the deciding parameters are the clamp voltage at the disconnect and the gate drive available. Our PCBA quote checklist page lists what a quote has to state so the switch, the clamp and the driver arrive as one set.
The sourcing side of this part is covered on the kitting service. For a group of parts that has to arrive together, that page covers how the kit is built and checked.
Questions we get on this code
Which resistance figure is real? Both, at their gate voltages. 3 milliohm at 10 V and 7 at 4.5 V, a ratio of 2.3 that changes the whole loss budget.
Is 60 V enough for a 48 V pack? At 58 V top of charge it is inside the absolute rating with 2 V to spare. A clamp is required, not optional.
Can it carry 270 A? The die can at a 25 C case. At 218 W of loss the package cannot, and the practical figure is nearer 50 to 70 A.
What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.