Contact Us

VBE165R05S

Brand: VBsemi
VBsemi VBE165R05S is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBE165R05S — Discrete & Power Semiconductors | Superb Automation

VBE165R05S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBE165R05S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBE165R05S: 650 V at 5 A with a one ohm channel

The VBE165R05S is a single N channel MOSFET in TO252 rated at 650 V, plus or minus 30 V on the gate, 5 A of drain current, with a threshold of 3.5 V and 1000 milliohm at a 10 V gate, on superjunction multi epitaxial silicon.

Six hundred and fifty volts is the workhorse class for offline power supplies, because a 265 V RMS mains peaks at 375 V and a flyback needs room for the reflected voltage and the leakage spike. A one ohm channel is a small die, and a small die is what a 5 to 20 W converter needs.

The interesting engineering is not the on resistance, it is the ratio of capacitance to current. At this die size the output capacitance is small, so the turn on loss into a capacitive load is small, and a converter can run at a higher frequency than a larger die would allow.

Key data for the VBE165R05S

ConfigurationSingle N channel
PackageTO252, DPAK, exposed drain tab
VDS650 V
VGSPlus or minus 30 V
Vth3.5 V
ID5 A
RDS(on) at 10 V1000 milliohm
TechnologySuperjunction, multi epitaxial
Body diodeIntrinsic, hard recovery characteristic of the class
Thermal pathDrain tab to copper or heatsink
Gate chargeNot published, small die means small charge
Typical useSmall offline flyback, auxiliary supply, start up circuit
IsolationNone, the tab is the drain

Why a one ohm part is not a downgrade

At 1 ohm and 1 A the loss is 1 W, which a DPAK passes comfortably. At 2 A it is 4 W, which needs a copper plane and some air. In a 15 W flyback running at 65 kHz the primary RMS current is around 0.4 A, so the conduction loss is 160 mW and the switching loss dominates.

For switching loss the parameters that matter are the output capacitance, the gate charge and the turn off time. A small die wins on all three. A larger, lower resistance die would add capacitance and gate charge and would run hotter at 1 A despite its lower resistance, because the switching loss rises faster than the conduction loss falls.

That is why the resistance column alone does not choose a part for a flyback. The rule of thumb is that the conduction loss should be roughly equal to the switching loss at the nominal load, and at 650 V that balance lands on a die sized for the load, not the largest die available.

The 650 V margin question

A 265 V RMS input peaks at 375 V. A flyback with a 100 V reflected voltage puts 475 V on the drain at turn off, and the leakage spike adds another 80 to 150 V depending on the transformer and the clamp. That lands at 555 to 625 V, which leaves 25 to 95 V of margin on a 650 V part.

At 230 V nominal, the same converter sees 325 V plus 100 plus a smaller spike, so the margin is wider. The tight case is the high line transient, and the usual answer is a snubber that clips the spike rather than a higher voltage part, because a 700 or 800 V part has a higher resistance at the same die size.

A 650 V superjunction has one more limit: the dV/dt during turn off. A fast drain rise can turn the device back on through the Miller capacitance, and the gate resistor has to be chosen with that in mind. The catalogue page does not publish the dV/dt rating, so the data sheet has to be checked before the gate resistor is fixed.

The small die also changes the gate drive requirement in a useful way. A one ohm, 650 V part has a gate charge in the region of a few nanocoulombs, so a controller with a weak output can drive it directly and still switch in tens of nanoseconds. That removes a driver from a 15 W converter and removes its quiescent current from the standby budget, which matters more than the conduction loss in a product that has to meet a standby power limit. A larger die would need a driver, and the driver would draw more than the converter saves.

The leakage inductance of the transformer decides how much of the 650 V budget is left for the bus. A 15 W flyback typically has 1 to 2 per cent leakage, and at 1 A of primary current that is a spike of tens of volts, which the snubber has to absorb. A snubber that is too small leaves the spike on the drain, and one that is too large wastes the energy it absorbs. The usual method is to size the snubber so the spike is 80 to 100 V above the reflected voltage and the resistor dissipates 1 to 2 per cent of the output power.

Where the part fits and where it does not

It fits an offline flyback under 20 W, an auxiliary supply inside a larger converter, a start up circuit that has to hold off the full bus, and a high voltage level shift where the current is small. It does not fit a PFC stage at 200 W, and it does not fit a bridge, because the body diode recovery in a superjunction is hard enough to destroy the opposite switch.

Our last time buy and LTB planning page covers how a long life product keeps a 650 V part available when the vendor moves the family to a new generation.

The sourcing side of this part is covered on the component shortage forecast. For a small converter that runs for years, that page covers how a shortage is seen before it stops a line.

Questions we get on this code

Can it be used at 400 V DC? Yes, with a clamp. Four hundred volts plus a leakage spike is close to the rating, and the margin for a mains transient is thin.

Is the 5 A rating continuous? Only with a heatsink. In a board with a copper plane the working current is nearer 1.5 A, which is what a 15 W flyback needs anyway.

Why does the catalogue give only one resistance column? Because the part is specified at a 10 V gate only. Below 10 V the resistance rises and the data sheet curve is needed.

What should a purchase order carry? Part number, TO252, reel size and date code. We confirm availability when the quantity is known.