VBC6P3033
Product Specifications
VBC6P3033
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBC6P3033 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBC6P3033: two -30 V P channels sharing one TSSOP8 body
The VBC6P3033 is a dual P channel MOSFET in a TSSOP8 body. Each half is rated at -30 V drain to source, plus or minus 20 V on the gate, a threshold of -1.7 V and -5.2 A of drain current. The catalogue gives 55 milliohm at a 2.5 V gate and 36 milliohm at 4.5 V, on trench silicon.
Two P channels in one eight pin body is a specific shape. It is not two parts in one box for convenience. The two dies sit on separate lead frames inside one moulded body, they share the same thermal path to the board, and they are cut from the same wafer, which is the reason a pair like this is chosen when the two halves have to behave the same way.
The gate figures are quoted as negative numbers because the device conducts when the gate is below the source. A threshold of -1.7 V means the channel starts to open when the gate sits 1.7 V under the source, and the resistance columns at -2.5 V and -4.5 V tell you how much further the gate has to go before the die is fully on.
Key data for the VBC6P3033
| Configuration | Dual P channel, two separate dies |
| Package | TSSOP8, 0.65 mm pitch, surface mount |
| VDS | -30 V |
| VGS | Plus or minus 20 V |
| Vth | -1.7 V typical |
| ID | -5.2 A per channel |
| RDS(on) at -2.5 V | 55 milliohm |
| RDS(on) at -4.5 V | 36 milliohm |
| Technology | Trench |
| Body diode | Intrinsic, cathode at drain |
| Thermal path | Eight leads into the copper, no exposed pad |
| Gate charge | Not on the catalogue page, ask for the curve before fixing a switching frequency |
| Isolation between halves | None beyond the body, the two drains are separate pins |
Why a matched pair instead of two singles
A pair from one wafer has a threshold spread that is tighter than two parts from two reels. In a circuit where the two halves work against each other, a push pull gate drive, a two rail disconnect that has to come up together, or a bridge whose two corners must not cross conduct, that spread is the parameter that decides whether the circuit is clean or has a shoot through window.
The second reason is board area. A TSSOP8 is 3 mm by 4.4 mm and carries eight leads. Two SOT-23 parts would take about the same area but with two separate thermal paths and two separate placements, and the pair keeps the gate and source nodes short, which matters at any frequency above a few hundred kilohertz.
The cost is thermal coupling. Both dies heat the same lead frame, so the junction temperature of one half is set by the total dissipation of the pair, not by its own. A circuit that runs one half at 1 W and the other at zero is not the same as one that runs both at 0.5 W, and the data sheet curve, if it is published for the pair, is drawn for the second case.
Reading the 2.5 V column on a P channel
Fifty five milliohm at -2.5 V against 36 milliohm at -4.5 V is a 35 per cent improvement, which tells you the die is not saturated at 2.5 V. A P channel has lower mobility than an N channel of the same area, so the same resistance needs more silicon or a higher overdrive, and a part that publishes both columns is giving the circuit engineer a choice between a logic level drive and a rail level drive.
A -2.5 V gate with a 3.3 V rail means the gate sits at 0.8 V and the source at 3.3 V, which a logic output can do directly if the output can sink the charge. The catch is that a P channel turns on when the driving pin goes low, so a microcontroller in reset, with its pins high impedance, leaves the switch in whatever state the gate resistor holds. That is a hardware decision, and it belongs on the board, not in the part number.
The 20 V gate window is generous for a 3.3 V or 5 V rail and tight for a 12 V rail switched at the source. If the source sits at 12 V and the gate is pulled to ground, the gate sees -12 V, which is inside the window but with little room for ringing. A 24 V rail with the same drive exceeds the window and needs a resistor divider or a zener at the gate.
Where the pair fits and where it does not
It fits two rail disconnect switches on a 5 V or 12 V board, a low current H bridge for a small actuator, a bidirectional analogue switch where the signal stays inside 30 V, and any place where two P channels have to track each other. It does not fit a load that draws more than about 2 A continuously per channel, because five amps in a TSSOP8 lead frame is a die figure and the leads are the limit.
Our power management cross reference page covers how a candidate is compared with an original on the parameters that decide behaviour, and a dual P channel is a case where threshold matching and the two resistance columns matter more than the headline current.
The sourcing side of this part is covered on the pin to pin cross reference. For a pair where both halves have to behave the same way, that page covers how a candidate is compared against the original on the parameters that are not printed in a headline.
Questions we get on this code
Can one half be used and the other left unconnected? Yes, but tie the unused gates to the source through a resistor rather than leaving them floating. A floating gate on a die that shares a lead frame with a switching neighbour picks up charge and can turn on.
What is the continuous current in a real board? At 36 milliohm and 2 A the loss is 144 mW per channel, which a TSSOP8 can pass with normal copper. At 5 A it is 900 mW, and the pair in still air will run hot. Derate from the 5.2 A figure and use the copper under the leads.
Is the body diode a problem? Only if the circuit reverse biases it while the channel is off. In a battery disconnect the diode conducts in the direction you are trying to block, so the pair has to be wired with the sources together or the diode blocks the wrong way.
What should a purchase order carry? Part number, TSSOP8, tape width and reel size. We confirm the reel size on the offer rather than assuming the usual 3000 pieces.