Contact Us

VBA5615

Brand: VBsemi
VBsemi VBA5615 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA5615 — Discrete & Power Semiconductors | Superb Automation

VBA5615

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA5615 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA5615: a 60 V N and P pair with higher resistance and a lower threshold

The VBA5615 is a complementary pair in an SOP8 body rated at plus or minus 60 V, with a plus or minus 20 V gate window, thresholds of 1.8 V on the N side and minus 1.7 V on the P side, currents of 9 A and minus 8 A, and resistances of 18 and 22 milliohm at 4.5 V falling to 15 and 17 milliohm at 10 V.

This is the near neighbour of the VBA5606 on the same shelf, and the pair of pages is instructive. The 5606 has 8 and 15 milliohm and a 2.8 V N threshold; the 5615 has 18 and 22 milliohm and a 1.8 V N threshold. One is built for low loss with a 10 V gate, the other for a lower gate drive with a higher resistance.

Which one belongs on a board is decided by the gate rail, not by the resistance. A board with a 10 V gate driver gets more from the 5606 at every current. A board with a 5 V gate rail cannot use the 5606 efficiently, because its N side needs more than 4.5 V to approach the published figure, and the 5615 is the part that works there.

Key data for the VBA5615

ConfigurationDual, one N channel and one P channel
PackageSOP8, surface mount, 1.27 mm pitch
VDSPlus or minus 60 V
VGSPlus or minus 20 V
Vth, N channel1.8 V
Vth, P channelMinus 1.7 V
ID, N channel9 A
ID, P channelMinus 8 A
RDS(on), N, 4.5 V and 10 V18 and 15 milliohm
RDS(on), P, 4.5 V and 10 V22 and 17 milliohm
TechnologyTrench
Gate chargeNot published on the catalogue page
Thermal pathEight leads, shared frame

Two thresholds that sit close together

A 1.8 V N threshold and a minus 1.7 V P threshold are close to symmetric in magnitude, which is worth noting because it makes a common gate drive behave consistently. At 4.5 V the N side has 2.7 V of overdrive and the P side has the same in magnitude, so both dies are in a similar state and neither dominates the crossover.

That symmetry is what a push pull stage wants. When the two thresholds are far apart, as on the 2.8 V part, the P side turns on first and the N side last, and the crossover interval is longer than it needs to be. With a symmetric pair the cross over is set by the gate drive current and the two gate charges rather than by the thresholds.

The resistance asymmetry remains, 15 against 17 milliohm at 10 V, which is only 13 per cent and much tighter than the usual factor of two. A pair this close in resistance is a matched output stage, and the loss in each direction is nearly the same.

Nine amps and the frame

At 15 milliohm and 9 A the N side dissipates 1.2 W. At 17 milliohm and 8 A the P side dissipates 1.1 W. A stage that conducts one device at a time runs near 1 W, which is at the top of what an SOP8 can pass in still air on a good copper landing.

Both devices at once in a bridge would be 2.3 W, which the body cannot pass. So the practical continuous current is nearer 5 to 6 A per direction, where the loss is 375 to 540 mW and the junction rise stays under 60 C.

The 60 V rating covers a 48 V rail with 12 V of margin, which is enough for a clamped load dump and not enough for an unclamped one. In an automotive or industrial input, the clamp is part of the circuit rather than an optional extra.

The choice between this part and the lower resistance pair on the same shelf is best made by measuring the gate waveform on the actual driver. A 5 V rail with a 1 A driver reaches 4.5 V in a few tens of nanoseconds and then holds, so the 18 milliohm column is the steady state number; a 10 V rail through a 10 ohm resistor reaches the plateau in a comparable time and settles at 15 milliohm. The difference in loss at 5 A is 75 mW per device, which is small, so the decision usually comes down to which gate rail the board already has rather than to the data sheet.

Where it fits

It fits a 48 V push pull stage driven from a 5 V or 10 V rail, a small motor driver with a symmetric output, a class D stage at moderate power, and a complementary level shifter on an industrial rail. It does not fit a 60 V rail, and it does not fit a continuous 9 A in a sealed enclosure.

Our material requirements planning page covers how a build plan becomes a purchase plan, which for a matched pair means ordering both halves in the same ratio as the boards.

The sourcing side of this part is covered on the sourcing audit trail. For a pair whose thresholds have to stay symmetric, that page covers what record is kept of the checks made before an order.

Questions we get on this code

Which of the two 60 V pairs should a 5 V system use? This one. Its N threshold of 1.8 V leaves 2.7 V of overdrive at 4.5 V, where the 8 milliohm part needs more than 4.5 V to reach its figure.

Are the two dies matched? In threshold they are nearly symmetric, and in resistance they differ by 13 per cent, which is close for a complementary pair.

What is the loss in a bridge at 4 A? About 240 mW in the N side and 270 mW in the P side per interval, plus the diode loss during the freewheel interval.

Is 60 V enough for a 36 V battery? A charged 36 V pack is 42 V, so the margin is 18 V, which is adequate with a clamp on the input.