VBA3316G
Product Specifications
VBA3316G
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA3316G from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA3316G: a 30 V half bridge in an SOP8
The VBA3316G is a half bridge in an SOP8 body, two N channel dies in series with the junction brought out, rated at 30 V per device with a plus or minus 20 V gate window, a 1.7 V threshold, currents quoted as 6.8 and 10 A and resistances of 22 milliohm at 4.5 V and 18 milliohm at 10 V.
A half bridge in one package is not the same product as two discrete parts, and the difference is the loop. The connection between the high side source and the low side drain is inside the moulding compound, so the inductance of that connection is a fraction of a nanosecond of trace, and the switch node ringing that a discrete pair produces is largely removed before it starts.
The price is that both dies sit on one lead frame and one body has to pass both losses. In a synchronous buck the low side carries the conduction loss for most of the period and the high side carries the switching loss, and in a small body the sum is what the thermal path has to move.
Key data for the VBA3316G
| Configuration | Half bridge, two N channel dies |
| Package | SOP8, surface mount, 1.27 mm pitch |
| VDS | 30 V per device |
| VGS | Plus or minus 20 V |
| Vth | 1.7 V |
| ID | 6.8 and 10 A, the two dies are not identical |
| RDS(on) at 4.5 V | 22 milliohm |
| RDS(on) at 10 V | 18 milliohm |
| Technology | Trench |
| High side drive | Needs a floating supply, a bootstrap capacitor and diode from outside |
| Dead time | Set by the driver, the package provides no interlock |
| Pin map | Not published on the catalogue page |
| Thermal path | Eight leads carrying both dies |
6.8 A and 10 A in the same body
Two different current figures for a half bridge are a gift, because they tell you which die is which. The die that carries the larger current is normally the low side, since in a buck it conducts for the larger part of the period at any duty below 50 per cent, and the die with the smaller figure is the high side, which spends most of its time off.
That asymmetry is the sensible way to build a half bridge for a step down converter, and it is the reason a half bridge package can beat two equal discrete parts. The high side die can be smaller, which means less gate charge to drive and less capacitance to charge at every switch node transition, and the low side die can be larger, which means lower conduction loss where the current actually flows for the longest time.
Equal currents in the catalogue would suggest two identical dies, which is a compromise. The 6.8 against 10 split suggests a purpose built pair, and a driver matched to it should have a stronger pull up for the low side and a faster pull down for the high side, or a single driver with enough current for both.
The high side gate and the bootstrap
The high side source sits on the switch node, so the gate has to be driven from a supply that rides on that node. The package does not include a bootstrap diode, so the board has to provide one, along with a capacitor sized for the gate charge of the high side die.
Gate charge is not on the catalogue page, so the capacitor cannot be sized from this page alone. The usual starting point is ten times the expected gate charge, and a wrong guess shows up as a high side that droops at high duty or fails to start at low duty. That is a measurable effect on the first prototype, and it is the reason the bootstrap capacitor is one of the first things to check on the bench.
Dead time is the other half of the driver decision. Both gates come out to separate pins, and the package provides no interlock, so shoot through is entirely a timing question. A driver with 20 to 100 ns of dead time suits a 30 V part at a few hundred kilohertz; a fixed 500 ns dead time forces the body diode to conduct for a long interval at light load and costs efficiency.
Where it fits
It fits a 12 V to 1.2 V or 12 V to 5 V synchronous buck at 5 to 8 A, a small motor drive with a complementary output, and a class D amplifier output stage at low power. It does not fit a 24 V rail, and it does not fit a converter where the two dies need to be different by more than the package offers.
Our power management cross reference page sets out how a half bridge package is compared with an original, and the checks are the pin map, the current split between the dies and the gate charge, not the headline resistance.
The sourcing side of this part is covered on the how to verify a drop in replacement. For a half bridge package where the two dies are not identical, that page sets out the checks before a substitute is accepted.
Questions we get on this code
Which die carries 10 A? The catalogue does not label them. Read the pin map on the data sheet, and in most packages of this kind the larger figure belongs to the low side.
Does it include the bootstrap diode? No. The board provides the diode and the capacitor, and the capacitor has to be sized from the gate charge.
Can the two dies be used as independent switches? Only if the switch node pin is accessible and both sources come out separately. Confirm on the data sheet rather than assuming.
Is 30 V enough for a 12 V input? Yes with margin, and the switch node ring stays below the rating as long as the input capacitor is close and the loop is short.