Contact Us

VBA1101N

Brand: VBsemi
VBsemi VBA1101N is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA1101N — Discrete & Power Semiconductors | Superb Automation

VBA1101N

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA1101N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA1101N: a 100 V N channel at 9 milliohm in an SOP8

The VBA1101N is a single N channel MOSFET in an SOP8 body with a 100 V drain to source rating, a plus or minus 20 V gate window, a threshold of 2.5 V, a drain current of 16 A, and an on resistance of 9 milliohm at a 10 V gate.

Nine milliohm at 100 V in an SOP8 is a strong die. It is the kind of resistance that usually comes in a DFN with an exposed pad, and it exists here because the SOP8 lead frame gives eight leads of copper to carry current and to spread heat.

The number that shapes every circuit around this part is the 2.5 V threshold. That is a standard level device, not a logic level one, and it needs 10 V of drive to reach the published resistance. A 5 V gate drive leaves 2.5 V of overdrive, which is workable but nowhere near the 9 milliohm column.

Key data for the VBA1101N

ConfigurationSingle N channel
PackageSOP8, surface mount, eight leads for current and heat
VDS100 V
VGSPlus or minus 20 V
Vth2.5 V
ID16 A
RDS(on) at 10 V9 milliohm
RDS(on) below 10 VNot published on the catalogue page, and a 2.5 V threshold means it is materially higher
TechnologyTrench
Gate chargeNot published on the catalogue page
Thermal limitAbout 1 to 1.5 W with the leads on copper, higher with a plane
Body diodeIntrinsic, anode at source

Sixteen amps at 9 milliohm, and the body behind it

At 16 A and 9 milliohm the conduction loss is 2.3 W. An SOP8 with all eight leads soldered to copper spreads that over a larger area than a SOT23, but 2.3 W still needs a real plane and some airflow. Without them the part runs near 150 C at that current.

The working figure is lower. With a lead frame in contact with 100 square millimetres of two ounce copper, junction to ambient lands near 45 to 60 degrees per watt, so a 100 C rise allows 1.7 to 2.2 W. At 9 milliohm that is 13 to 15 A, which is close to the rating and is a sign that the 16 A figure was set with a good pad in mind rather than an impossible one.

In a 60 C ambient the same arithmetic gives 10 to 12 A. Above that the copper has to grow, or the part moves to a body with an exposed pad.

Why the threshold matters more than the resistance here

A 2.5 V threshold means the channel starts conducting at 2.5 V and reaches a usable resistance somewhere above 5 V. At a 10 V gate the overdrive is 7.5 V and the die is fully on. At a 5 V gate the overdrive is 2.5 V, a third of that, and the resistance is typically two to three times higher, which puts a 10 A load at 1.8 to 2.7 W instead of 0.9.

For a 48 V system this is normally fine, because a 10 V or 12 V gate supply exists. For a 12 V system the gate can be driven to 10 V from the rail with a bootstrap, which is the standard arrangement in a synchronous buck. For a 5 V system the part is the wrong choice and a logic level 100 V die is right.

The gate window of 20 V leaves room for a 12 V rail drive with a clamp, and the gate charge of a 9 milliohm die is substantial, so the driver has to be sized for the charge rather than for the average current. Expect tens of nanocoulombs and a driver able to source and sink an amp.

Where an SOP8 100 V part earns its place

It sits between the small SOT23 parts and the DFN power packages. It is the right choice where the board cannot take an exposed pad, where the assembly process is a simple reflow with no thermal pad stencil, where the current is 5 to 12 A, and where the rail is 48 V or a 60 V battery string.

Typical uses are the low side switch of a non isolated converter, a load switch on a 48 V bus, a battery disconnect, and the synchronous rectifier of a low voltage output. The body diode recovery of a 100 V die is the parameter to check in a synchronous use, and this page does not publish it.

Our incoming inspection plan page covers what is checked before a reel enters a line, and a 100 V part at 9 milliohm is worth checking for authenticity, because the same body is used for parts whose die is a third of the size.

The sourcing side of this part is covered on the PCBA quote checklist. For a power switch that goes onto an assembled board, that page covers what has to be settled before a quote is firm.

Questions we get on this code

Can it be driven from a 5 V gate driver? Yes, and the part will work, but at a resistance well above 9 milliohm. Use it that way only where the current is low enough that the extra loss is acceptable.

Is 16 A real in a closed box? No. Plan on 10 to 12 A on a good pad, less without a plane.

Is the SOP8 footprint the standard one? Yes, the standard eight lead body. Confirm the pin assignment on the data sheet, because some parts in this body put the drain on four leads and others on two.

What is the alternative with a lower threshold? The same family carries 100 V parts at 1.8 V threshold. Ask for the code if a 5 V drive is fixed.