HXN40047
Product Specifications
HXN40047
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXN40047 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXN40047: five watts across 4.4 to 5 GHz with the match on the carrier
The HXN40047 is the bottom rung of the Hisiwell ladder that covers 4.4 to 5 GHz. The index row reads 4.4 to 5 GHz, saturated output at least 37 dBm, gain at least 12 dB, drain efficiency at least 45 per cent, 28 V drain rail, plus or minus 0.8 dB of flatness, continuous wave. The product page adds two facts the table does not carry: input and output impedance are both 50 ohm, and the match is built by in plane synthesis on a film hybrid carrier rather than left to the board.
Five watts of radio frequency at 45 per cent efficiency draws 11.1 W from the rail, which at 28 V is 0.40 A, and leaves 6.1 W of heat on the flange. Drive at the 12 dB gain floor is 25 dBm, which is 0.32 W, so a small driver stage two or three transistors back is enough to reach saturation. Those are calculated figures from the published rows, not vendor numbers, and they are the shape of the budget a system engineer works with first.
The band is the reason to look at this part. 4.4 to 5 GHz covers the lower half of C band, the 4.4 to 5 GHz fixed link allocations, and the uplink and downlink windows that satellite terminals and laboratory instruments use. Six hundred megahertz of span at a 4.70 GHz centre is 12.8 per cent fractional bandwidth, and a part that holds 37 dBm with plus or minus 0.8 dB across it does the work that a narrower cell plus a retune would otherwise do.
For a buyer the practical question is whether five watts is the right rung. It sits below the 10 W and 20 W members on the same band, so it is the natural choice for a driver stage, for a short range link, or for a product where the antenna gain does the rest. Where the output has to be higher, the same carrier and the same 28 V rail carry larger members, and the RF component sourcing page lists how we hold those parts against a bill of materials.
The parameter rows Hisiwell publishes for HXN40047
| Part class | Gallium nitride power transistor, internally matched |
| Frequency range | 4.4 to 5 GHz |
| Bandwidth, calculated | 600 MHz, 12.8 per cent fractional at a 4.70 GHz centre |
| Saturation output power as published | at least 37 dBm |
| Saturation output power in watts, calculated | 5.01 W |
| Gain as published | at least 12 dB |
| Drain efficiency as published | at least 45 per cent |
| Drain voltage | 28 V |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Input impedance | 50 ohm |
| Output impedance | 50 ohm |
| Match technology as described by the vendor | in plane matching synthesis, film hybrid integration |
| Output at 1 dB compression | not published, the index prints a slash |
| DC input at saturation, calculated | 11.1 W |
| Drain current at saturation, calculated | 0.40 A at 28 V |
| Dissipation at saturation, calculated | 6.1 W |
| Dissipation if efficiency falls to 40 per cent, calculated | 12.5 W |
| Drive power for the rated output, calculated | 25 dBm, 0.32 W |
| Output per 100 MHz of the band, calculated | 0.84 W |
| Load voltage at saturation into 50 ohm, calculated | 15.8 V RMS, 22.4 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text, one image on the product page |
| Scattering parameters | not published |
| Pinch off voltage and gate bias point | not published |
| Operating and storage temperature | not published |
| Moisture level and floor life | not published |
| Orderable addendum and packing | not published |
| Neighbour on the same band at 40 dBm | HXN40048, same rail, same gain floor |
| Neighbour on the same band at 53 dBm, pulsed | HXN40053, same rail, 10 dB gain |
What 600 MHz of matched bandwidth actually buys
A plus or minus 0.8 dB window across 4.4 to 5 GHz means one amplifier covers the whole lower C band allocation without a switched filter bank or a mechanical retune. In a laboratory instrument that is the difference between one box and three, and in a fixed link terminal it is the difference between a per channel build and a single board that ships against several channel plans.
The cost of that window sits in the efficiency row. The vendor prints 45 per cent for this member, and the wider band members on neighbouring bands print the same figure, so the flatness is not being paid for with efficiency here. What it is paid for with is the match on the carrier: the synthesised network holds 50 ohm over the octave and a half, and the board behind it sees a load it does not have to tune.
Where the margin matters is at the band edges. A part published as at least 37 dBm across the band normally holds that figure at the two ends, which is where the match is hardest and where the drive level has to be highest. Budget the driver for the edge case and the mid band will sit above the target, which is the direction a link budget wants.
The 4.4 to 5 GHz ladder from 37 to 53 dBm
Hisiwell publishes seven members on this band, and the steps are not evenly spaced. Against this part at 5.01 W the next rung is 2.0 times the power, then 3.98, 10.0, 19.95, 25.12 and 39.81 times. In decibels that is 0, 3, 6, 10, 13, 14 and 16 dB, so a system that needs 6 dB more output can take HXN40049 and keep the same 28 V rail, while a step of 10 dB lands on HXN40050, which is also the first member where the gain floor drops from 12 to 11 dB.
Two rows in that ladder break the pattern and are worth naming. HXN40052 is the 51 dBm member and the only one on 32 V instead of 28 V, so it is not a drop in replacement for a 28 V board even though the band and the gain match. HXN40053 is the 53 dBm member and the only pulsed one, at 100 microseconds and 10 per cent duty, so the heat it puts on the flange is a tenth of its saturation dissipation.
For a cross reference the ladder is more useful than a single row, because a replacement has to match the rail and the mode before it matches the power. Our RF power transistor cross reference page sets out the sequence we use: rail, mode, band, then power and gain.
What to settle before the part goes on a board
The gate bias point is not published, so the first bench task is a bias sweep against quiescent current, not a plug and play. The vendor states 28 V on the drain and 50 ohm at both ports and stops there; there is no pinch off voltage, no recommended quiescent drain current and no gate voltage window on the page. Treat the first article as a characterisation exercise.
Heat is the second item. At 6.1 W of dissipation a carrier offering 3 C per watt rises about 18 C over the case and one offering 5 C per watt rises 31 C, so a modest heatsink is enough at this power level. The temperature limit itself is not published, which means the sink has to be sized against the system limit rather than against a vendor curve.
The third item is the drive chain. A 25 dBm drive is one watt class territory, and the gain flatness of the driver sets how much of the plus or minus 0.8 dB budget is left at the antenna. Our guide to choosing an RF amplifier works through that chain from the driver back to the source.
Questions buyers ask about HXN40047
Is it continuous wave or pulsed. The index row says continuous wave, and the 6.1 W of dissipation is a steady load rather than an average over a duty cycle, so a pulsed system can use it but gains nothing in the thermal budget from the fact.
Can it run from a 32 V or 48 V bus. The published rail is 28 V. The 51 dBm member on this band is the 32 V part and the ladder has no 48 V member here, so a higher bus needs a step down feed rather than a different transistor.
Does the part come with a data sheet. The vendor publishes an index row and a short product page, and no data sheet appears on either, so there are no curves, no scattering parameters and no thermal derating to read. Everything on this page that is not in those two sources is marked calculated.
How is it supplied. There is no orderable addendum, no packing column and no marking code on the vendor page, so the purchase order has to name the band, the rail and the quantity, and we confirm the reel or tray with the factory before a date is quoted. Lead time for the ladder comes through the RF procurement route, where the part sits on the same line as the smaller and larger members.