100E511MW2500X KYOCERA AVX RF Capacitor
Product Specifications
PRODUCT SPECIFICATIONS
100E511MW2500X — KYOCERA AVX RF/Microwave Capacitor
Product Overview
The 100E511MW2500X is a RF/microwave ceramic capacitor manufactured by KYOCERA AVX., with high-Q, low-loss performance characteristics. Designed for ghz / microwave (series dependent) applications — suitable for rf matching / microwave / communication.
Technical Specifications
| Part Number | 100E511MW2500X |
| Manufacturer | KYOCERA AVX |
| Frequency Range | GHz / Microwave (Series Dependent) |
| Q Factor | High Q (Series Dependent) |
| RF Suitable | YES |
| High Q | YES |
| Low Loss | YES |
| Tolerance | Refer to datasheet |
| Package / Case Style | Refer to datasheet |
| Dielectric Material | Refer to datasheet |
| Temperature Coefficient | Refer to datasheet |
| Operating Temperature Range | Refer to datasheet |
| Termination Finish | Refer to datasheet |
| Mounting Type | Surface Mount (SMD/SMT) |
| RoHS Compliance | RoHS Compliant |
| REACH Compliance | REACH Compliant |
| Country of Origin | United States |
| Manufacturer Part Number | 100E511MW2500X |
| Data Confidence | Series Based |
| Verification Note | Requires ATC datasheet confirmation |
Key Features
- High Q Factor — Excellent quality factor for low-loss RF performance at operating frequency.
- Low ESR — Low Equivalent Series Resistance ensures minimal signal attenuation in RF paths.
- RF/Microwave Optimized — Designed for ghz / microwave (series dependent) frequency range with stable capacitance and high self-resonant frequency.
- Surface Mount Package — Compatible with standard SMT reflow soldering and automated PCB assembly.
- Rugged Construction — KYOCERA AVX capacitors manufactured in certified facilities with consistent batch performance.
Applications
- RF Matching — Impedance matching networks for RF power amplifiers in base stations, small cells, and repeaters.
- Microwave — Microwave circuit applications including couplers, filters, and resonant structures.
- Communication — Telecom equipment — 5G NR base stations, microwave backhaul, satellite communication systems.
- Medical — Medical electronics — MRI systems, RF ablation equipment, medical telemetry devices.
- Aerospace — Aerospace and defense — radar systems, electronic warfare, avionics, satellite payloads.
Compatible and Alternative Part Numbers
- Equivalent Manufacturers: Passive Plus, Presidio Components, Johanson Technology, Knowles/Dielectric Labs, Murata, TDK
- Same Series Alternatives: Other capacitance, voltage, tolerance, and package variants within the KYOCERA AVX product family
- Cross-Reference Guidance: When substituting, verify capacitance value, voltage rating, tolerance, package dimensions, dielectric type, and RF performance (Q factor, ESR, SRF)
About KYOCERA AVX
KYOCERA AVX capacitors are manufactured in ISO 9001 certified facilities and widely specified in reference designs from Analog Devices, Texas Instruments, MACOM, Qorvo, Broadcom, and other leading RF semiconductor manufacturers. Key applications include 5G NR base stations, satellite communication, military radar, MRI medical imaging, and automotive radar systems.
About Superb Automation — Trusted KYOCERA AVX Supplier
Superb Automation is a trusted electronic components supplier. We provide 100% genuine KYOCERA AVX capacitors with full warranty, lot traceability, and competitive pricing. Our service includes component sourcing, PCB manufacturing, PCBA assembly, and global logistics with engineering support.
Why Source 100E511MW2500X from Superb Automation?
- Trusted Supplier — 100% genuine, factory-original KYOCERA AVX products with full warranty and lot traceability.
- Competitive Pricing — Volume discounts available. Prototype and sample quantities supported.
- Fast Quotation — RFQs processed within hours. In-stock items ship same/next business day.
- Engineering Support — FAE team assists with capacitor selection, S-parameter simulation, and cross-reference.
- One-Stop Solution — Capacitors + PCB + PCBA assembly from a single supplier.
- Quality Assurance — ESD-protected handling, visual inspection, electrical verification before shipment.
- Global Logistics — International shipping with full export documentation.
Ordering Information
To order 100E511MW2500X or any KYOCERA AVX capacitor, contact us with: Part Number, Quantity, Target Price, Delivery Destination, Required Date. Contact: Info@superb-tech.com | www.superb-tech.com
100E511MW2500X: 510 pF at 2500 V in the case E body
Read 100E511MW2500X from the left and every character was fixed before the order went out. 100 is the porcelain high radio frequency power series, E is the case, 511 is the capacitance code where the first two digits are the significant figures and the third is the number of zeros, which makes this a 510 pF part, M is the tolerance code at plus or minus 20 percent, W is tin and lead solder plated over a nickel barrier, 2500 is the working voltage in volts DC, and X is laser marking.
Case E is the 9.65 mm square porcelain body carrying 510 pF with M tolerance at 2500 V, 4.32 mm maximum thickness with a 1.02 mm maximum termination overlap. At 2500 V this one stores 1594 microjoule and holds 1275 nanocoulomb, and both figures follow from the working voltage rather than from the package, so the voltage field is the one that fixes the body.
The dielectric is P90 porcelain at plus 90 plus or minus 30 ppm per degree C and the operating range is minus 55 to plus 125 degrees C with no derating, a span over which this 510 pF part in M tolerance holds 1594 microjoule at 2500 V. No packaging letter sits in 100E511MW2500X, so the reel or the tray comes from the mechanical configuration table: tape and reel at 250 pieces, or a tray of 24 or 96 for the W finish.
| Series and case | 100E, case E, 9.65 mm by 9.65 mm |
| Capacitance | 510 pF, code 511 |
| Tolerance | M, plus or minus 20 percent, a window of 408 to 612 pF |
| Working voltage | 2500 VDC, 1768 V RMS at 0.707 times the DC rating |
| Dielectric withstanding | 3000 V for five seconds, 120 percent of the working voltage |
| Life test | 2500 V for 2000 hours at 125 degrees C, 100 percent of the working voltage |
| Temperature coefficient | plus 90 plus or minus 30 ppm per degree C |
| Operating range | minus 55 to plus 125 degrees C with no derating of the working voltage |
| Insulation resistance | 10^5 Mohm minimum at 25 degrees C and 10^4 Mohm minimum at 125 degrees C, both measured at 500 VDC |
| Leakage floor | 25 nA at 2500 V and 250 nA at 125 degrees C, computed from those resistance floors |
| Stored energy | 1594 microjoule at the working voltage, from one half C V squared |
| Stored charge | 1275 nanocoulomb at the working voltage |
| Reactance at 150 MHz | 2.08 ohm nominal |
| Reactance at 500 MHz | 0.62 ohm nominal |
| Series resonance | plotted against capacitance for the series, read from that curve rather than quoted here |
| ESR | curves at 30, 150, 500 and 1000 MHz, printed at 10, 100, 1000 and 5100 pF for the series |
| Quality factor | Greater than 10,000 at 1 MHz from 1 pF to 1000 pF, and at 1 kHz above that range |
| Termination | W, tin and lead solder plated over a nickel barrier, a lead bearing finish |
| Marking and packing | laser marking; tape and reel at 250 pieces, or a tray of 24 or 96 pieces |
| Mounting pad | A .405, B .050, C .325 and D .425 inch on the normal density pad, .385, .030, .325 and .385 on the high density one |
What 510 pF does from 30 MHz to 1 GHz
At 30 MHz this 510 pF body presents 10.4 ohm, at 150 MHz 2.08 ohm, at 500 MHz 0.62 ohm and at 1 GHz 0.31 ohm. Above a few hundred picofarads the 510 pF part is a bypass and a DC block, so the useful question is how low the impedance stays at the top of the band, and 0.31 ohm at 1 GHz answers it better than the nominal capacitance does.
Tolerance is easier to judge in reactance than in picofarads. At 500 MHz the M window of 408 to 612 pF lands at 0.52 ohm at the top of the window and 0.78 ohm at the bottom, a spread of 0.26 ohm between the two ends against a 0.624 ohm nominal, which is 41.7 percent of that reactance. A 510 pF part in a match or a filter has to hold the M letter, while the same part used as a bypass at 500 MHz does not notice a 41.7 percent spread.
For the 510 pF code in M tolerance the data sheet draws series resonance against capacitance and prints the points at 10, 100, 1000 and 5100 pF rather than a number for every value. Scaling the nearest published point of 365 MHz at 100 pF by the square root of the capacitance ratio gives about 162 MHz for 510 pF if the series inductance stayed put, and that is an estimate for a starting point, not a specification: the resonance curve is the document that decides, because the internal electrode pattern moves the inductance with the value.
Where a 510 pF case E part is chosen
Above a few hundred picofarads the part is a bypass and a DC block: the return path behind a power stage, the reservoir at the feed point of a bias line, the shunt leg of a low pass filter, and the coupling element into a load that has to stay at a low impedance across a band rather than at a point. At 500 MHz this one is 0.62 ohm, 1.2 percent of a 50 ohm line, so the match is already made at the low end of the band.
The circuit families the series names are high frequency and radio frequency power amplifiers, transmitters, antenna tuning, plasma chambers and magnetic resonance coils, and every one of them asks the same two questions of a 510 pF part in M tolerance: how much current the body carries at the frequency of operation, and how far the value may drift before the stage notices.
At 2500 V the withstanding test on this 510 pF code is 3000 V for five seconds, 120 percent of the rating, and the 2000 hour life test at 125 degrees C runs at 2500 V, 100 percent. On this 510 pF part in M tolerance the resistance floor of 10^5 Mohm at 25 degrees C puts 25 nA of leakage at the full rating and the 10^4 Mohm floor at 125 degrees C puts 250 nA there, so a 1 Mohm bias node sees 250 mV at the hot end.
Questions that arrive with a shortage quote
Can the M code be swapped for another grade on a shortage? The ceramic and the case do not change and the letter is a sort, so the question is only how much window the circuit absorbs. At 510 pF the M window is 408 to 612 pF, the next grade tighter is K at plus or minus 10 percent, and there is no looser grade in this list. At 500 MHz those ends land at 0.52 ohm at the top of the window and 0.78 ohm at the bottom, a spread of 0.26 ohm against a 0.624 ohm nominal, so a match or a filter has to hold the M letter while a bypass position does not care. On 100E511MW2500X we quote the letter on the order and state on the quotation the grade we can actually ship, so the two never get mixed on the line.
What has to be on the certificate for 100E511MW2500X? Four things that a broker line often leaves off: the date code and the lot, the measured capacitance with the test frequency stated, which is 1 MHz for this value, the withstanding result against the 3000 V level for five seconds, and the finish, because W is lead bearing and a restricted build cannot take it without a deviation. A 510 pF part in M tolerance also has to carry its tolerance letter on the paperwork, since the value alone does not tell the line which window arrived.
Is the W finish the only option? No. On the 510 pF body in M tolerance W is tin and lead solder plated over a nickel barrier and is lead bearing; T is the RoHS compliant tin over a nickel barrier on the same body, P is the heavy tin and lead pellet, CA is a gold chip, MS is a microstrip style with silver leads and AR, AW and RW are the leaded styles. The termination letter changes the mounting and the compliance statement, not the 510 pF or the 2500 V, so a line that has been buying W and is asked to move to T is changing a finish rather than a capacitor. Packing on a 510 pF order follows the same table: tape and reel at 250 pieces, or a tray of 24 or 96.
What to send with an enquiry
Four fields decide the price and the date: quantity, target date, the full order code 100E511MW2500X with the tolerance and termination letters, and the packing the line accepts. Send the whole string for 100E511MW2500X and we check it against the current revision, then confirm date codes, packing and country of origin on the quotation. The One Stop RF Supply page sets out how a radio frequency bill is sourced and what a second source has to prove, the Obsolete RF Part Replacement page covers the route when a value is on allocation, and the Date Code Management page sets out the packing, kitting and inspection options a production line asks for.