Contact Us

LTM4676AEY#PBF

Brand: Analog Devices
Analog Devices LTM4676AEY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM4676AEY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM4676AEY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM4676AEY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM4676AEY#PBF: the E grade of the 26 A digital module, and what the suffix changes

The LTM4676AEY#PBF is the E grade of the dual 13 A or single 26 A PMBus module in the 16 mm by 16 mm by 5.01 mm package. The front page numbers are shared with the I grade: 4.5 V to 26.5 V in, 0.5 V to 5.5 V out, plus or minus 0.5 percent of dc error, plus or minus 2.5 percent of current readback at 10 A, a 40 ms turn-on time and pin compatibility with the dual 18 A LTM4677. The suffix decision is about the guarantee, and the practical decisions that surround it are the input range and the 3.3 g body.

Published values

ParameterValue
Input voltage4.5 V to 26.5 V
Output voltage0.5 V to 5.5 V
Output currentdual 13 A or single 26 A
DC output errorplus or minus 0.5 percent over temperature
Current readbackplus or minus 2.5 percent at 10 A
Turn-on time40 ms
Digital interface400 kHz PMBus, 16-bit ADC
Thermal resistance10.3 degree C per W
E grade rangeminus 40 degree C to 125 degree C
PackageBGA, 16 mm x 16 mm x 5.01 mm
Weight3.3 g
Pin compatibilityLTM4677 dual 18 A

Two rails at 13 A each is the configuration most builds use

Thirteen amps at 3.3 V is 42.9 W and thirteen at 1.2 V is 15.6 W, so the two channels are rarely loaded the same and the loss is not shared evenly. At 90 percent the 3.3 V channel dissipates 4.8 W and the 1.2 V one 1.7 W, and the 10.3 degree C per W figure is a package number rather than a per channel one, so the hotter channel sets the junction temperature for both.

That asymmetry is what makes the single 26 A configuration attractive when only one rail is needed: paralleling the two channels shares the loss and halves the per channel current, and the phases can be interleaved so the input ripple drops. The cost is that both channels then follow one setpoint, which is fine for a core rail and wrong for a pair of independent supplies.

A 3.3 g module with 400 kHz of bus traffic next to it

The PMBus runs at 400 kHz and polls to 125 Hz, and a 16-bit ADC with a 0.5 percent dc accuracy is a measurement channel inside a switching regulator. The bus is a two wire interface with all seven bit addresses supported, so several modules share it, and the address is set by a resistor rather than by a pin strap: two modules at the same address on one bus is the most common commissioning fault on a board with more than one of these.

The 3.3 g body and the 16 mm footprint also mean the module is a mechanical element of the board. It has to sit on copper, it has to survive the reflow of a large thermal mass, and it has to be supported in the oven. On a board with connectors and a stiffener this is routine; on a thin card with no support the module's weight and the ball array are the two things that decide whether the assembly survives handling.

The E grade against a 105 degree C ambient

Both E and I order codes are listed at minus 40 degree C to 125 degree C, so the suffix is not a wider window. At 105 degree C ambient and 4.8 W of loss the rise is 49 degree C and the junction is at 154 degree C, which neither grade allows. The answer for that ambient is a lower loss configuration, a heatsink on the board or a different module, not a different suffix on this one.

The 26.5 V input maximum is the other hard line. A 24 V rail at plus ten percent is 26.4 V, which is inside it by 0.1 V, and a 24 V rail with any transient is outside. A build fed from a 24 V backplane needs a clamp or a module with a higher input rating, and the 0.5 V output at that input is a 1.9 percent duty cycle that the loop cannot produce anyway.

The pages that answer this most often are the power management cross reference for the family alternatives, OEM procurement for the acceptance test, and component lead time solutions for the case where a replacement has to be fitted before the next build.

Two questions buyers ask

Can two modules share one rail? Yes, the part supports parallel and current share operation across multiple modules, which is how the 26 A figure is extended. Each module needs its own address on the bus and the share bus has to be connected, and the loop compensation in each module has to be set for the paralleled case rather than for a single module.

What is the difference between the two thermal numbers? The data sheet gives 10.3 and 6.2 degree C per W, which are two different test board conditions rather than two grades. The lower number belongs to the board with more copper, so a build that quotes the 6.2 figure has to provide that copper; quoting it on a two layer board understates the rise by about 40 percent.

The address resistor decides whether the bus works at all

The module supports all seven bit slave addresses and the address is set by a resistor to a defined level rather than by a pin strap that reads a binary code. On a board with more than one module the addresses have to be distinct before anything else is checked, because two modules at the same address answer the same command and the reading that comes back is a collision rather than a value.

The practical sequence on a new board is to read the address of each module with the bus master before any regulation setting is written, and to record it against the rail name. A module that reports the same address as another is a resistor value error, not a firmware problem, and the fault shows up as a voltage readback that jumps between two rails rather than as a bus error.