Contact Us

HMC907A-Die

Brand: Analog Devices
Analog Devices HMC907A-Die is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC907A-Die — Analog & Mixed-Signal ICs | Superb Automation

HMC907A-Die

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC907A-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC907A die: 3.5 W of DC into a 3.94 square millimetre amplifier

The HMC907A is a gallium arsenide pHEMT distributed power amplifier die covering 0.2 GHz to 22 GHz with 14 dB of gain, 28 dBm of output power at one decibel compression, 41 dBm of output third order intercept and 350 mA from a single 10 V supply. The die measures 2.92 mm by 1.35 mm by 0.1 mm, the input and output are matched to 50 ohm on chip, and every published figure was taken with the chip in a fixture connected by two 0.025 mm wire bonds of at least 0.31 mm. There is no gate pin to adjust, which is the first thing that separates it from the rest of the wideband pHEMT family.

Published values

ParameterValue
Frequency range0.2 GHz to 22 GHz
Gain12 dB minimum, 14 dB typical over 0.2 GHz to 8 GHz
Gain flatness0.7 dB from DC to 12 GHz
Output power at 1 dB compression25 dBm minimum, 28 dBm typical
Saturated output power29 to 30 dBm typical
Output third order intercept40 to 41 dBm typical at 16 dBm per tone
Output second order intercept41 to 42 dBm typical
Noise figure3 to 6 dB depending on band
Supply10 V typical, 8 V minimum, 11 V maximum, 350 mA
Gain variation over temperature0.004 to 0.007 dB per degree
Die size2.92 mm by 1.35 mm by 0.1 mm
Matching50 ohm input and output on chip

What 350 mA at 10 V does inside a 3.9 square millimetre die

10 V at 350 mA is 3.5 W of DC input before any radio frequency leaves the part. At the 28 dBm compression point the output is 0.63 W, so 2.87 W becomes heat, and the die face is 2.92 mm by 1.35 mm, which is 3.94 square millimetres. That is 0.73 W per square millimetre, a number worth comparing against any other amplifier being considered for the same socket, because it sets the carrier, the attach and the cooling rather than the gain.

The 0.1 mm substrate is the reason the heat has to leave through the backside into a carrier instead of spreading sideways. A copper molybdenum carrier, or a copper tungsten one where the expansion has to match the alumina around it, with a void free eutectic or sintered attach, is what the die expects. A gap in the attach under the output stage becomes a local hot spot, and because the amplifier is distributed the hot spot sits in the middle of the output line rather than at one edge.

22 GHz from a distributed stage, and what the bonds do to it

A distributed amplifier trades gain per stage for bandwidth by absorbing the transistor capacitances into artificial transmission lines, which is why 14 dB is available across more than five octaves and why the gain falls gently rather than rolling off. The same structure makes the part sensitive to whatever sits between the die and the board, because the on chip matching stops at the bond pad.

A 0.025 mm wire of 0.31 mm length is roughly 0.25 nanohenry, which is about 35 ohm at 22 GHz and 1.6 ohm at 1 GHz. Two of them in parallel halve that, and the data sheet figures are taken with two. A single ribbon of the same length is not the same component, so an assembly that switches from two round bonds to one ribbon changes the match at the top of the band and reads as a gain error that no amount of bias adjustment will remove.

Self biased, so there is no gate to set and nothing to sequence

A single positive 10 V supply sets the operating point, with no negative rail and no VGG pin. That removes the power up sequence problem that the gated parts in this family bring, and it removes the bias controller. The trade is that the drain current is fixed by the internal network, so the 350 mA cannot be trimmed per part, and the supply tolerance in the table runs from 8 V to 11 V rather than a single number.

For a multi chip module the part is supplied as Known Good Die and the assembly is the qualification. What has to be recorded for each build is the bond length and count at both ports, the attach void percentage under the die, and the carrier material, because those three set the measured gain and the junction temperature and a replacement lot with the same part number will not reproduce the result without them.

For a board that has to keep running while a reel runs out, the RF component sourcing page is where the family alternatives sit, how to choose an RF amplifier is the check list before a substitute goes in, and obsolete RF part replacement is how a gap is covered without a new line item.

Two questions buyers ask

Does the HMC907A need a negative gate supply? No. It is self biased from a single positive 10 V rail at 350 mA, so there is no VGG pin and no power up sequence beyond bringing the drain up with the input drive off.

Can it be used at 28 dBm continuously? The 28 dBm figure is the one decibel compression point measured in a 50 ohm fixture, not a continuous power rating. The die dissipates 2.87 W at that point, and what limits continuous operation is the carrier and the attach, not the number in the table.