Contact Us

ADMV7710

Brand: Analog Devices
Analog Devices ADMV7710 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADMV7710 — Analog & Mixed-Signal ICs | Superb Automation

ADMV7710

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADMV7710 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADMV7710: 29 dBm at 71 GHz to 76 GHz from a die three millimetres square

The ADMV7710 is a gallium arsenide pHEMT medium power amplifier die for the 71 GHz to 76 GHz E band, with 24 dB of gain, 28 dBm of output power at one decibel compression, 29 dBm saturated, 34 dBm of output third order intercept and a temperature compensated on chip detector, from a 4 V supply at 800 mA. The die is 2.999 mm by 3.999 mm by 0.05 mm and needs no external matching. At these frequencies the die thickness and the bond wire geometry are part of the electrical specification, not just the assembly drawing.

Published values

ParameterValue
Frequency range71 GHz to 76 GHz
Gain24 dB typical
Output power at one decibel compression28 dBm typical
Saturated output power29 dBm typical
Output third order intercept34 dBm typical
Input return loss18 dB typical
Output return loss10 dB typical
Supply4 V at 800 mA
Power added efficiency20 percent, which puts the drain current near 1 A at saturation
Die size2.999 mm by 3.999 mm by 0.05 mm

The quiescent current is not the current at power

800 mA at 4 V is 3.2 W of DC input. Twenty percent power added efficiency at 29 dBm of output, which is 0.79 W, needs 3.9 W of DC input, and 3.9 W at 4 V is 0.98 A. The drain current at saturation is roughly a quarter higher than the quiescent figure, and on a 4 V rail a quarter of an amp is enough to move the bias point if the supply has any series resistance.

The published 20 percent efficiency is the number that makes the thermal budget work. 3.9 W in and 0.79 W out leaves 3.1 W of heat in a die of 12 square millimetres, which at 0.05 mm thickness has very little thermal spreading of its own. The carrier does the spreading, and the attach has to be void free under the whole output section rather than just under the centre.

Fifty micrometre thickness and the bond wires

A 0.05 mm die is thin enough that the assembly process matters more than the handling jig. The ground path is through the die bottom, so the attach is both the thermal and the electrical return: an incomplete attach is an inductor in the source of every transistor on the die, which at 76 GHz is gain lost and match shifted.

The input and output pads are matched on chip, but a single 0.025 mm bond wire is about 0.25 nanohenry, which is 12 ohm at 76 GHz. Two wires in parallel halve that and also halve the current density in each. The data sheet values are taken with short bonds, so a loop of wire of twice the length is a different amplifier at the top of the band.

Ten decibels of output return loss

A 10 dB return loss is a 1.9 voltage standing wave ratio. In E band a waveguide transition, a filter or an antenna can all present an impedance that moves with frequency, and at the output of a 29 dBm stage the load line moves with it. The usual practice is to keep a short, well matched run to the next component and to check the match of that component at the band edges.

The 18 dB input return loss is the better of the two, which helps when the driver is a variable attenuator or a filter with a poor match of its own. The asymmetry is deliberate: the output is where the power is, and a wider match there costs efficiency.

When an order code in this family cannot be found, the RF component sourcing page lists what else does the same job, one stop RF supply covers what to check before a part is dropped into an existing board, and how to choose an RF amplifier is the route we take on a live shortage.

Two questions buyers ask

Does the part need external matching in E band? No. The input and output are matched to 50 ohm on die, so the assembly is a bond wire and a transition rather than a matching network. The bond wire length is what sets the match at the top of the band.

Is 800 mA the current to budget for the supply? No. 800 mA is the quiescent figure. At 29 dBm with 20 percent efficiency the DC input is about 3.9 W, which at 4 V is about 0.98 A during operation.