ADG5412BRUZ
Product Specifications
ADG5412BRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG5412BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG5412BRUZ: four independent switches with a 48 V ceiling
The ADG5412BRUZ is a quad single pole single throw switch in a 16-lead TSSOP, with each switch turning on for a logic 1 at its own control pin. It belongs to the same latch up proof, trench isolated family as the ADG5408 multiplexers, so it carries the same 48 V absolute maximum supply rating and the same 8 kV human body model rating, but it is wired as four independent channels rather than a decode.
Published values
| Parameter | Value |
|---|---|
| Channels | 4 independent SPST, on for logic 1 |
| Supply | 9 V to 22 V dual, 9 V to 40 V single |
| Absolute maximum supply | 48 V |
| On resistance | below 10 ohm |
| Charge injection | 240 pC typ at 15 V rails, 310 pC at 20 V |
| Off isolation | -78 dB at 1 MHz |
| Supply current | 55 uA max |
| ESD | 8 kV human body model |
| Thermal resistance | 112.6 C/W TSSOP, 30.4 C/W LFCSP |
| Package and range | 16-lead TSSOP, -40 C to +125 C |
The package is the thermal decision
Two packages carry this die and the difference is not cosmetic. The TSSOP body sits at 112.6 C/W junction to ambient and the LFCSP at 30.4 C/W, so the same silicon in the same board position runs about 3.7 times hotter in the leaded body for a given dissipation.
Half a watt in the TSSOP is a 56 C rise before the ambient is counted, which puts a 70 C cabinet at the edge of the 125 C limit. The same half watt in the LFCSP is a 15 C rise. When a board carries four channels that each pass a continuous current, the package choice is what decides whether the part survives, not the on resistance.
Charge injection at the two rail settings
The data sheet gives 240 pC typical on 15 V rails and 310 pC on 20 V rails. Into a 1 nF hold capacitor that is 240 mV and 310 mV of step, which is why a switch carrying an analog level into a converter is usually followed by a buffer rather than wired straight to the sampling node.
Into a 10 nF capacitor the same charge is 24 mV, and the trade is settling time against pedestal: the larger capacitor settles more slowly through the switch resistance, so the turn on window has to be checked with the capacitor the board will actually fit.
Four switches, four independent decisions
Because each channel has its own control pin, this part is used to route a signal, disconnect a load, or short a resistor in and out of a gain network. The switches conduct in both directions when on, so a channel can be placed anywhere in a signal path without regard to the direction of current.
The ADG5413 order code shares the package and has two of its four channels with inverted logic, which matters when a processor resets with its pins low: the ADG5412 is then off, the ADG5413 has two channels on. That difference is a power up state decision, not a performance one.
Replacement checks
Footprint compatible parts from lower voltage families will switch faster and inject less charge, and they will also give up the 48 V ceiling. On a board where the switch protects an input from an external harness, that ceiling is the requirement and the switching speed is the luxury.
The checks in order are supply span, channel count and control polarity, then thermal resistance in the package the board uses. The pages below hold the family alternatives, the acceptance sequence and the shortage routine.
Two pages worth reading before a purchase order goes out are the ADI second source page and how to verify a drop in replacement; the first lists what else fits the socket, the second is the test sequence for a drop in, and BOM shortage recovery covers the case where the shortage is already on the line.
Two questions buyers ask
Can two channels be paralleled for lower resistance? The vendor does not specify paralleling, and the two channels do not share a control node, so the switch that turns on first carries the current until the second closes. Treat the channels as independent.
What is the difference between the ADG5412BRUZ and ADG5413BRUZ? Two of the four channels on the ADG5413 have inverted control logic. The die, the supply range and the on resistance are the same.