Contact Us

AD8629ARZ

Brand: Analog Devices
Analog Devices AD8629ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8629ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD8629ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8629ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8629ARZ: dual zero drift amplifier in an 8-lead SOIC

The AD8629ARZ is the dual auto-zero amplifier in an 8-lead narrow SOIC_N body. It carries the same two 1 uV channels as the MSOP version, with 2 MHz of gain bandwidth, 1.0 mA maximum per amplifier and 50 us of overload recovery, in the package that can be reworked by hand and probed with a scope.

Published values

ParameterValue
Offset voltage1 uV typical, 5 uV maximum
Offset voltage drift0.002 uV/C typical, 0.02 uV/C maximum
Input bias current30 pA typical, 100 pA maximum
Supply current per amplifier0.75 mA typical, 1.0 mA maximum at 2.7 V
Gain bandwidth2 MHz at 5 V
Slew rate1.0 V/us
Voltage noise density22 nV/root Hz at 1 kHz
CMRR120 dB typical at 5 V
Overload recovery50 us
Output swing4.99 V minimum high into 100 k at 5 V
Supply range2.7 V to 5.5 V single supply
Package8-lead narrow body SOIC_N (R-8)

Differential wiring on a 1.27 mm pitch

A difference stage built from the two halves needs the two input pairs to see the same environment: same trace length, same distance from the supply pins, and a ground or guard trace between the inverting and non-inverting nodes. The SOIC pitch makes that easier than the MSOP because the pins are twice as far apart, and it makes the leakage path between adjacent inputs longer, which is what a 100 pA bias current budget cares about.

Board leakage is the quiet failure mode here. At 100 pA maximum of bias current, a 100 MOhm residue or flux path adds a microvolt, which equals the offset. Wash and bake the board, keep the input traces short, and put the guard at the same potential as the input common mode.

Drift over a sealed enclosure

0.02 uV/C maximum over 165 C is 3.3 uV, so a channel calibrated at 25 C is 3.3 uV out at 125 C. Against a 5 uV offset that is a two thirds change, and against a 1 mV signal it is a third of a percent. A conventional amplifier with 1 uV/C of drift would be 165 uV out over the same range, which is why the auto-zero part appears in instruments that are sealed and cannot be re-zeroed.

The output swing of 4.99 V minimum into 100 k at 5 V leaves 10 mV, which is 130 codes of a 16-bit converter on a 5 V span. A rail-to-rail converter input therefore still loses the top 130 codes, and a gain stage that has to use the whole span needs headroom or a slightly lower reference.

Where the two channels should not be used

Both channels share a supply pin and a ground pin, so the return current of one channel flows through the same bond wire as the other. In a high gain channel next to a channel driving a cable, that shared impedance couples the load current into the sensitive input. Keep the two functions on separate packages when one of them drives anything heavier than 10 k, and use the pair only for two similar signal channels.

The pages that answer this most often are component lead time solutions for the family alternatives, the obsolete part cross reference hub for the acceptance test, and OEM procurement for the case where a replacement has to be fitted before the next build.

Two questions buyers ask

Is the SOIC version electrically identical to the MSOP version? Yes, same die and same limits. The SOIC has a lower thermal resistance and a wider lead pitch, which is the only practical difference.

Does the AD8629 need a clock or a capacitor? No. The auto-zero loop is internal and the data sheet requires no external component, which keeps the parts count at one package and one decoupling capacitor for two channels.