AD8604ARUZ
Product Specifications
AD8604ARUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8604ARUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8604ARUZ: four 8 MHz amplifiers in a 14-lead TSSOP
The AD8604ARUZ is the four channel member of the AD8601/AD8602/AD8604 family in a 14-lead TSSOP, giving four 8.4 MHz channels at 750 uA each with a 600 uV maximum offset and 33 nV/root Hz of noise. It is the package for a four channel acquisition front end that needs bandwidth, where four separate singles would not fit and four micropower parts would not be fast enough.
Published values
| Parameter | Value |
|---|---|
| Offset voltage, A grade | 80 uV typical, 600 uV maximum at 25 C, 1700 uV maximum over temperature |
| Offset voltage drift | 2 uV/C typical |
| Input bias current | 0.2 pA typical, 60 pA maximum |
| Supply current, four channels | 3 mA typical, 4.8 mA maximum at 5 V |
| Gain bandwidth | 8.4 MHz at 5 V |
| Slew rate | 6 V/us at 5 V |
| Voltage noise density | 33 nV/root Hz at 1 kHz |
| Open loop gain | 30 V/mV minimum |
| Settling to 0.01% | under 1 us at 5 V |
| Phase margin | 55 degrees |
| Package | 14-lead TSSOP, 4.4 mm body |
| Supply range | 2.7 V to 5.5 V single supply |
Four channels at three milliamps
The headline current is per amplifier, so the quad draws 3 mA typical and 4.8 mA maximum from a 5 V rail, which is 24 mW. That is a real load on a battery instrument and a trivial one on a mains powered data acquisition board. Decide which of the two the product is before choosing the channel count, because four micropower channels at 40 uA each would cost 0.6 mW and 385 kHz.
Sharing a die between four channels
A quad shares one supply pin pair and one ground return, so a fast edge on one channel couples into the other three through the package inductance and the shared return. At 6 V/us the disturbance is short and small, but a 12-bit converter sampling two channels simultaneously will see it. Either stagger the conversions or give each channel its own decoupling capacitor at the pin, which is the cheaper of the two answers at these currents.
What the offset tolerance does to the input range
The 600 uV maximum at room temperature applies with the input between 0 V and 5 V, and it grows to 1.7 mV over the full temperature range. Since the four channels are independent samples rather than a matched set, a differential measurement between two channels carries up to twice that error. Where the four channels have to agree, either calibrate each one or use a part with a guaranteed offset in the tens of microvolts.
Where a 14-lead TSSOP quad fits
Four channel multiplexed inputs, four pole active filters in one package, quadrature encoder buffers, and four channel LED or laser diode monitors are the usual sockets. The 4.4 mm body keeps four channels inside the width of two SOIC-8 packages, which is usually the reason the quad was chosen in the first place.
Where a customer needs a second position on this part, the amplifier cross reference is the starting point, the ADC and DAC cross reference sets out the checks a substitution has to pass, and one stop BOM sourcing is the short lead time route we quote against.
Two questions buyers ask
Is the AD8604ARUZ pin compatible with other quads in the family? It follows the standard 14-lead quad pinout, so the footprint is shared with many quads, but the electrical behaviour of a substitute has to be checked channel by channel.
What happens with a 1 nF load on each output? With 55 degrees of phase margin at 5 V, a 1 nF load will ring and can oscillate. Isolate each output with a series resistor and take the feedback before it.