Contact Us

AD8542ARMZ

Brand: Analog Devices
Analog Devices AD8542ARMZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8542ARMZ — Analog & Mixed-Signal ICs | Superb Automation

AD8542ARMZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8542ARMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8542ARMZ: two rail-to-rail amplifiers in an 8-lead MSOP

The AD8542ARMZ packs two of the 45 uA CMOS rail-to-rail amplifiers into an 8-lead MSOP, which is the package to pick when the board is already tight and a second amplifier channel is needed next to the first. It carries the same 1 MHz bandwidth and 6 mV maximum offset as the single, at 90 uA for the pair.

Published values

ParameterValue
Offset voltage1 mV typical, 6 mV maximum per amplifier
Offset voltage drift4 uV/C typical
Input bias current4 pA typical, 60 pA maximum
Supply current, both channels80 uA typical, 120 uA maximum at 5 V
Gain bandwidth1 MHz at 5 V supply
Slew rate0.45 V/us typical, 0.92 V/us at 5 V
Voltage noise density40 nV/root Hz at 1 kHz
Output swing at 1 mA4.9 V minimum high, 25 mV typical low at 5 V supply
Thermal resistance, MSOP-8142 C/W junction to ambient
Package footprint3 mm by 3 mm body, 0.65 mm pitch
Phase margin67 degrees
Supply range2.7 V to 5.5 V single supply

Why the MSOP body changes the thermal answer, not the electrical one

The die inside the MSOP and the SOIC version of this dual are the same, so offset, drift, bandwidth and noise do not change when one package is swapped for the other. What changes is the path from junction to air: 142 C/W for the MSOP against 120 C/W for the 8-lead SOIC_N. At 120 uA and 5 V the part dissipates 0.6 mW, so the junction sits 0.09 C above ambient in the MSOP and the difference is academic. It stops being academic in a sealed box at 85 C with a regulator beside it, where every degree of margin counts.

When a pair in one body is the wrong choice

Two amplifiers on one die share a supply pin and a ground return, so a fast transient on one channel appears on the other through that shared impedance. At 1 MHz and 0.4 V/us the crosstalk is small, but in a board where both channels drive separate ADC inputs the shared return is the usual source of a few hundred microvolts of channel to channel error. Star the ground at the package pin rather than letting the two channels share a trace back to the connector.

Separation is also a reason to keep the two channels out of one package: a sensor input and a comparator threshold on the same die will couple, and the fixed cost of a second package is often cheaper than the rework.

Reading the datasheet numbers for a dual

Every current, noise and offset figure on this page is per amplifier, so the pair draws 90 uA typical and 120 uA maximum, and the two offsets are independent samples from the same distribution rather than matched pairs. If a differential measurement depends on the two offsets tracking, budget the full 6 mV maximum on each channel instead of assuming cancellation.

Assembly notes

0.65 mm pitch on a 3 mm body is within the reach of a standard stencil and reflow profile, but the paste volume matters: too much paste lifts the body and opens the corner pins. The same board can usually take the SOIC version on a small adapter, which is worth knowing when a build has to ship before the MSOP reel arrives.

Two pages worth reading before a purchase order goes out are BOM shortage recovery and the pin to pin cross reference; the first lists what else fits the socket, the second is the test sequence for a drop in, and how to verify a drop in replacement covers the case where the shortage is already on the line.

Two questions buyers ask

Is the AD8542ARMZ interchangeable with the AD8542ARZ on the same board? No, the footprints differ. The electrical behaviour is the same die, so a board that is being revised can move between the two packages without changing the loop, but an existing board needs an adapter.

How much current does the pair draw at 3.3 V? About 76 uA typical for both channels, since the per amplifier figure falls to 38 uA at 2.7 V, and the maximum at that rail is 55 uA per amplifier.