Contact Us

AD8510ARMZ

Brand: Analog Devices
Analog Devices AD8510ARMZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8510ARMZ — Analog & Mixed-Signal ICs | Superb Automation

AD8510ARMZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8510ARMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8510ARMZ: a JFET input amplifier with 25 pA of bias current

The AD8510ARMZ is the single amplifier of a JFET input family in an 8-lead MSOP. Bias current is 25 pA typical at room temperature, offset is 400 microvolts maximum on the B grade and 900 on the A, gain bandwidth is 8 MHz, slew rate is 20 V per microsecond, settling to 0.1 percent is 0.4 microseconds, noise is 8 nV per root hertz at 1 kHz and distortion is 0.0005 percent. Supply spans plus or minus 5 V to plus or minus 15 V.

Published values

ParameterValue
Input bias current25 pA typical, 75 pA maximum at plus or minus 5 V
Bias current at temperature0.7 nA at 85 degrees, 7.5 nA at 125
Input offset, A grade0.9 mV maximum at plus or minus 5 V, 1.8 over temperature
Input offset, B grade0.4 mV maximum, 0.8 over temperature
Offset drift1.7 microvolts per degree typical on A, 0.9 on B; 12 and 5 maximum
Gain bandwidth8 MHz
Slew rate20 V per microsecond
Settling0.4 microseconds to 0.1 percent on a 4 V step
Noise8 nV per root hertz at 1 kHz, 34 at 10 Hz, 2.4 microvolts peak to peak
Distortion0.0005 percent at 1 kHz
Input common mode2.0 V above the negative rail to 2.5 V below the positive one on a plus or minus 5 V supply
CMRR86 dB minimum
Supply current2.0 mA typical, 2.3 maximum per amplifier
Output current40 mA typical, 54 maximum
Package8-lead MSOP

Bias current that doubles every ten degrees

Twenty five picoamps at 25 degrees becomes 0.7 nA at 85 and 7.5 nA at 125, a factor of 300 across the industrial range. That is the behaviour of a JFET gate, and it is the number to use when a photodiode or an electrometer input has to work in a hot enclosure. The 25 pA headline is a room temperature figure and nothing more.

What the bias current does depends entirely on the source impedance. Into 1 Mohm, 7.5 nA is 7.5 mV, which dwarfs the 0.9 mV offset. Into 10 kohm it is 75 microvolts and disappears. A photodiode transimpedance stage with a 10 Mohm feedback resistor is therefore in the regime where the hot bias current, not the offset, sets the error floor.

The input common mode range is not the supply range

On a plus or minus 5 V supply the inputs work from 2.0 V above the negative rail to 2.5 V below the positive one, which is a 4.5 V window rather than 10 V. A follower whose input approaches the positive rail will clip, and the datasheet is explicit about it. On a plus or minus 15 V supply the window is wider but still short of both rails.

The output, by contrast, reaches within 0.7 V of each rail into 2 kohm and within 0.3 V into 10 kohm, and it sources 40 mA. The asymmetry between a limited input range and a wide output swing is normal for a JFET input stage and is the first thing to check when a follower built from this part misbehaves near a rail.

Forty four degrees of phase margin and a capacitive load

The phase margin is 44.5 degrees, which is stable but not generous. A cable or a large capacitor directly on the output will ring, and the usual fix is a small series resistor between the output and the load, inside the feedback loop for a cable or outside it for a capacitor.

Settling of 0.4 microseconds to 0.1 percent on a 4 V step is fast for a JFET input part and is the reason it turns up in multiplexed data acquisition and in sample and hold circuits. The settling to 0.001 percent is not specified in the same line, so a 16-bit acquisition that needs 15 microvolts of residual has to either measure it or allow more time than the 0.1 percent figure suggests.

Two pages worth reading before a purchase order goes out are the amplifier cross reference and medical device components; the first lists what else fits the socket, the second is the test sequence for a drop in, and component lead time solutions covers the case where the shortage is already on the line.

Two questions buyers ask about the JFET input amplifier

Is the AD8510 the single version of the AD8512? Yes. The same die as a single in an 8-lead package, with the same electrical table and the same two grades.

What is the maximum supply? Plus or minus 15 V nominal, with the PSRR specified from plus or minus 4.5 V to plus or minus 18 V. A 36 V single supply is outside the intended use.