Contact Us

AD8352ACPZ-R7

Brand: Analog Devices
Analog Devices AD8352ACPZ-R7 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8352ACPZ-R7 — Analog & Mixed-Signal ICs | Superb Automation

AD8352ACPZ-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8352ACPZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8352ACPZ-R7: 41 dBm of Output IP3 at 150 MHz From a 3 mm Package

The AD8352 is a differential radio frequency and intermediate frequency amplifier with a 2.2 GHz -3 dB bandwidth at a voltage gain of 10 dB, a gain adjustable from 3 dB to 25 dB with a single resistor, and an output third order intercept of 41 dBm at 150 MHz. It runs from 3 V to 5.5 V at 37 mA typical, drops to 5 mA in power-down, and settles and recovers from overdrive in under 2 ns. In a receiver front end it is the stage that decides how much blocking a converter behind it can survive, and 41 dBm of output intercept in a 3 mm by 3 mm body is the reason it appears in differential converter drive chains.

Gain set by one resistor, distortion set by a second network

Voltage gain is set by a single resistor between the gain adjust pins, with 3 dB to 25 dB available, and the input resistance stays at 3 kohm independent of that gain. That independence is the useful part: a differential source filter sees the same load at every gain setting, so the filter does not have to be retuned when the gain is changed in production. Broadband distortion is then trimmed with a second resistor and capacitor network, which is a separate adjustment from gain, so the two can be optimized in sequence on the same board.

What 41 dBm means against a converter's full scale

An output intercept of 41 dBm in 50 ohm is 25.6 V peak to peak, which no 5 V part can deliver, so the figure describes the extrapolated third order behaviour rather than a level the amplifier will reach. At the 1 dB compression point of 15.7 dBm into a 1 kohm load with a 178 ohm gain resistor, the output is about 2 V peak to peak, and third order products at that level are roughly 50 dB down, which is -34 dBm. Relating that to a 16 bit converter with a 2 V peak to peak full scale: -34 dBm is far below one least significant bit, so the amplifier is not the limit at full scale, and the limit moves to the converter when the signal drops.

ParameterValueWhat it decides
Bandwidth2.2 GHz at 10 dB gainUsable as an intermediate frequency gain block
Gain range3 dB to 25 dBOne resistor between the gain adjust pins
Input resistance3 kohm, gain independentThe source filter does not change with gain
Input noise2.7 nV per root hertz2.7 uV rms over 1 MHz, referred to input
Second harmonic at 10 MHz-86 dBcEven order terms need a balanced source
Third harmonic at 10 MHz-82 dBcOdd order terms dominate a single tone test
Third harmonic at 190 MHz-87 dBcHolds at the top of the band
Output IP3 at 150 MHz41 dBmExtrapolated, equals 25.6 V peak to peak
1 dB compression15.7 dBm into 1 kohmAbout 2 V peak to peak at the output
Slew rate8 V per nanosecondFull scale steps in under a nanosecond
Overdrive recoveryUnder 2 nsA blocking event does not lose the next sample
Supply and current3 V to 5.5 V at 37 mA0.185 W at 5 V, power-down at 5 mA
Package3 mm by 3 mm LFCSPThermal path for a part that runs warm

The pin that sets distortion rather than gain

The distortion trim network is a resistor and capacitor from the internal nodes to ground, and it works by adding a controlled amount of cancellation against the output stage's own nonlinearity. The adjustment is frequency dependent, so a value chosen for 70 MHz will not be right at 190 MHz, and the data sheet gives the harmonic figures at three frequencies precisely because one setting cannot cover the whole band. A board that is trimmed at one frequency and used at another will show worse harmonics than the table.

Balanced source and the even order terms

The -86 dBc second harmonic at 10 MHz is measured with a differential input. A single ended source into one side of the input converts the input's own second order term into a differential error and the figure degrades, which is why the data sheet specifies a balun or a differential source for the best numbers. The input resistance of 3 kohm is also differential, so a single ended 50 ohm source needs a matching network and not a direct connection.

Sourcing a differential amplifier with a converter behind it

This part is normally bought together with the converter it drives, and the two have to be compared as a pair: the amplifier's compression point against the converter's full scale, and the amplifier's noise against the converter's least significant bit. Where a bill of materials is being consolidated around one converter family, the parts that match are listed through ADC DAC cross reference, and the general route for this class of radio part is in RF component sourcing. Where the amplifier is the part that is short, the options are set out in BOM shortage recovery.