Contact Us

AD8328ARQ

Brand: Analog Devices
Analog Devices AD8328ARQ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8328ARQ — Analog & Mixed-Signal ICs | Superb Automation

AD8328ARQ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8328ARQ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8328ARQ: 60 dBmV Into 75 Ohm Is 1 V RMS and 13.3 mA of Cable Current

The AD8328 is a 5 V upstream cable line driver for DOCSIS and EuroDOCSIS reverse path transmitters. The headline output figure is 60 dBmV, and that number is worth converting before anything else is decided: 0 dBmV is 1 mV across 75 ohm, so 60 dBmV is 1.0 V rms, 2.83 V peak to peak, 11.25 dBm and 13.3 mA of rms current into the cable. A driver that is specified at that level is being asked for 13.3 mA of signal current on a 5 V rail while it also holds a defined output impedance, and both of those terms are what make the part a line driver rather than a general purpose amplifier.

What the 59 dB gain span actually covers

Gain is set over a 59 dB range in 1 dB steps through the serial word, which gives 59 usable codes and a step size that is the same as the accuracy the loop can resolve. In a reverse path the transmit level is trimmed against the headend's received power, so a 1 dB step is the granularity the operator's commissioning procedure works in, and any driver with a coarser step forces the modem to move in larger increments than the ranging algorithm expects. The upper bandwidth of 107 MHz is stated over the full gain range, which matters because a part that only holds bandwidth at low gain is unusable at the high end of the span.

The distortion and noise numbers, converted

Spurious free dynamic range is quoted at 60 dBmV output as -57.5 dBc at 21 MHz and -54 dBc at 65 MHz. Relative to a 1 V rms carrier, -57.5 dBc is a worst spur at 1.33 mV rms, and -54 dBc at 65 MHz is 2.0 mV rms. Output noise at minimum gain is 1.2 nV per root hertz, which across a 6.4 MHz upstream channel is 3.0 uV rms, or 0.96 dBmV. That places the noise floor 59 dB below a 60 dBmV carrier, so over the middle of the band the spur and the noise land in the same region, and neither can be treated as the only limit.

ParameterValueWhat it decides
Supply5 V singleFixes the headroom for a 2.83 V peak to peak output
Quiescent current98 mA typical0.49 W in the driver alone before signal current
Sleep current2.6 mAThe state between bursts in a burst mode upstream
Power-down current20 uAFull shutdown, not the same pin state as sleep
Gain span59 dB in 1 dB stepsMatches the ranging step the headend commissions in
Output level60 dBmV1 V rms, 2.83 V peak to peak into 75 ohm
Output current at that level13.3 mA rmsSets the supply decoupling and the return path
Differential output impedance300 ohm, both statesConstant load whether the transmitter is on or off
SFDR at 21 MHz-57.5 dBc1.33 mV rms worst spur at 60 dBmV
SFDR at 65 MHz-54 dBc2.0 mV rms worst spur at 60 dBmV
Output noise at minimum gain1.2 nV per root hertz3.0 uV rms over a 6.4 MHz channel
Upper bandwidth107 MHz, full gain rangeTwo thirds of margin above a 65 MHz edge
Package20-lead QSOPThermal path for 0.49 W of quiescent loss

The 300 ohm output in both states

The differential output impedance stays at 300 ohm with the transmitter enabled and with it disabled. That is a system requirement rather than a convenience: the upstream diplexer and the cable tap are matched to the line, and a driver that goes high impedance when the burst ends produces a reflection at every burst boundary. Keeping the termination constant is what allows several modems on one tap to share the return path without the idle ones disturbing the active one.

Supply and thermal budget

Quiescent current is 98 mA typical at maximum gain, in a 20-lead QSOP, so the package is dissipating close to half a watt before the output signal current is counted. The rail decoupling and the copper under the part are part of the electrical result, not a formality. The sleep state at 2.6 mA is two orders of magnitude below the active state, so a receiver that gates the transmitter between bursts saves the bulk of the budget, and the 20 uA power-down state is reserved for the line being out of service.

Where this part sits in a sourcing decision

A reverse path driver is usually bought against an existing modem or amplifier bill of materials, and the order code carries the package and temperature grade. Substitution across this family is not free: the gain span, the step size and the output impedance in the disabled state all have to match, and a part with the same pin count but a different output termination changes the diplexer match. Buyers who need the exact order code with the package suffix intact can check availability against RF component sourcing, and where the original code is short, the same family is listed under one stop RF supply. When the substitution is forced by a lead time, the electrical comparison that has to be made is set out in pin to pin cross reference.