AD8305ACPZ
Product Specifications
AD8305ACPZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8305ACPZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8305ACPZ: 100 dB Logarithmic Converter for Photodiode Current
The AD8305ACPZ converts a photodiode current into a voltage proportional to its logarithm, over five decades from 10 nA to 1 mA, which is 100 dB of range with 0.1 dB of law conformance. The nominal slope is 10 mV per dB, or 200 mV per decade, and the intercept is nominally 1 nA set by a single external resistor. It runs from a 3 V to 12 V total supply, single or dual, draws about 5 mA, comes in a 3 mm by 3 mm 16-lead LFCSP, and includes a buffer amplifier and the reference needed for a full log ratio measurement. It is built for fibre optic receive power measurement, where the signal spans exactly this range.
Published values
| Parameter | Value |
|---|---|
| Input current range | 10 nA to 1 mA, five decades |
| Dynamic range | 100 dB |
| Law conformance | 0.1 dB from 10 nA to 1 mA |
| Slope | 10 mV per dB, nominally 200 mV per decade |
| Intercept | 1 nA nominal, set by an external resistor |
| Supply | 3 V to 12 V total, single or dual |
| Quiescent current | About 5 mA |
| Output | Buffered, with slope and intercept adjustment |
| Extra function | Log ratio of two currents |
| Package | 16-lead LFCSP, 3 mm by 3 mm |
What 0.1 dB of conformance means in optical power
Optical power is expressed in dBm, and 0.1 dB of error is 2.3 percent of the power, which in a receiver chain is a small fraction of the total link budget. That is why the specification is quoted in dB rather than in percent: a converter that is linear to 2 percent over five decades is doing something a linear amplifier with five decades of range could not do at all. The error budget around it is dominated by the photodiode's responsivity drift and by the intercept resistor, not by the log converter, so a 1 percent resistor at the intercept pin is adequate and a precision reference for it is not necessary.
The intercept resistor sets where the output crosses zero
The 1 nA nominal intercept comes from a 10 microamp reference current through a 200 kohm resistor, and changing that resistor moves the intercept, which shifts the whole output curve vertically. In a calibrated instrument the intercept is trimmed once, and the drift of that resistor then appears as a scale error of the reading in dB. A 100 parts per million per degree resistor gives 0.01 dB per degree of drift, which over 50 degrees is 0.5 dB, larger than the converter's own conformance error. Use a 25 parts per million part or trim in software.
Guard rings and the 10 nA floor
Ten nanoamps is small enough that board leakage competes with the signal. At 10 nA, a 10 Gohm leakage path carries the same current, and a contaminated board with 100 Mohm of surface leakage carries 100 times the signal. The input pin needs a guard ring driven at the same potential, the photodiode should be close to the package, and the board must be cleaned. Conformal coating after assembly is the standard practice in optical modules for exactly this reason. Without those measures the converter works and the low end of the range is wrong, which is the failure mode that survives a bench test at high optical power.
Availability and second sourcing
A log converter is replaced only by another log converter with the same slope and intercept convention, because the firmware calibration assumes both. An amplifier plus a logarithmic computation in software is an alternative but loses the five decade instantaneous range. The amplifier cross reference page lists the log and detector family, the ADI part second source page separates the parts with the same slope convention, and the lead time page shows availability.