AD8009ARZ
Product Specifications
AD8009ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8009ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8009ARZ: 5,500 V per Microsecond for Pulse Work
The AD8009ARZ is a current feedback amplifier built for the case where the edge, not the sine wave, is the signal. Slew rate is 5,500 V per microsecond on a 4 V step at a gain of two, rise time is 545 ps on a 2 V step, and the -3 dB bandwidth is 700 MHz at a gain of two with 440 MHz of large signal bandwidth. It settles to 0.1 percent in 10 ns on a 2 V step, delivers 175 mA of output current, and runs from plus and minus 5 V on 14 mA. The 545 ps rise time and the 2 V step are consistent: an average of 3,670 V per microsecond over that edge is what a 5,500 V per microsecond part produces once the settling tail is included.
Published values
| Parameter | Value |
|---|---|
| Slew rate | 5,500 V per microsecond on a 4 V step, gain of two |
| Rise time | 545 ps on a 2 V step, gain of two |
| Bandwidth | 700 MHz at a gain of two, 440 MHz large signal |
| Settling time | 10 ns to 0.1 percent, 2 V step |
| Output current | 175 mA |
| Third order intercept | 26 dBm at 70 MHz, gain of ten |
| Output power | 10 dBm at 70 MHz |
| Video | 0.01 percent differential gain, 0.01 degree differential phase |
| Gain flatness | 0.1 dB to 75 MHz |
| Supply | Plus and minus 5 V |
| Supply current | 14 mA typical |
| Bodies | 8-lead SOIC and 5-lead SOT-23 |
175 mA is four video loads, not one
The output stage is rated at 175 mA, which is what four back terminated 75 ohm video loads draw in parallel at full swing, or a single 30 ohm load at 5 V. That is the number to use when a distribution amplifier drives several cables from one output: the parallel impedance falls, the current rises, and the part is specified to survive it. Two consequences follow. First, plus and minus 5 V at 14 mA is 140 mW of quiescent power, and the load current adds to it, so a package that is fine at idle needs copper under it when driving four cables. Second, the return path of four coaxial cables carries the sum of the return currents, so the ground plane and the connector placement matter as much as the amplifier choice.
26 dBm of intercept at a gain of ten
Third order intercept of 26 dBm at 70 MHz at a gain of ten is an extrapolated figure, not an output level: it describes how fast the third order terms grow as the input rises. Used as an IF gain stage, the part holds a clean signal at 10 dBm of output power at 70 MHz, which is 2.24 V peak to peak into 50 ohm. Pushing beyond that moves the distortion products up quickly because the intercept line steepens for a current feedback stage at high output. A board that needs more output power than this at 70 MHz needs a different topology, not a higher supply.
Slew rate and full power bandwidth are the same question
A 440 MHz large signal bandwidth at 2 V peak to peak needs 2.76 V per nanosecond of output slope, which is 2,760 V per microsecond, and the 5,500 V per microsecond figure leaves about two times margin for the settling tail. Run the same part at 4 V peak to peak and the full power bandwidth falls to about 220 MHz for the same reason. This is the arithmetic that explains why a stage that looks fine at low amplitude falls apart when the signal grows, and it is why the amplitude and the frequency have to be quoted together in any comparison of high speed parts.
The two bodies are not interchangeable
The 8-lead SOIC and the 5-lead SOT-23 have different pinouts and different thermal paths, so an order code that ends in RT is not a smaller version of one that ends in R. The SOT-23 has no spare pin for a feedback node, so the board around it has to be arranged for the five lead pinout, and the SOIC keeps the conventional arrangement. When a program is being second sourced or a build is being moved between two assembly houses, the suffix decides which board is being populated. The amplifier cross reference page groups the pulse and video parts by slew rate, the ADI part second source page covers the grades that are genuinely equivalent, and the obsolete part cross reference hub covers the case where the exact suffix has already been discontinued.