AD637JRZ
Product Specifications
AD637JRZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD637JRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD637JRZ: 0.02 Percent Nonlinearity From dc to 8 MHz of RMS Conversion
The AD637JRZ is a complete true rms to dc converter, and the numbers in the features list are what make it a measurement instrument rather than a detector: 0.02 percent maximum nonlinearity over a 0 V to 2 V rms input, 0.1 percent additional error up to a crest factor of 3, 8 MHz of bandwidth at 2 V rms and 600 kHz at 100 mV rms. It computes true rms, mean square, absolute value and a dB output covering 60 dB, and the chip select pin puts the output into a three state condition when the part is powered down, so several converters can share one bus. Inputs are protected against overload beyond the supply levels and are not damaged if the supplies are lost, which matters in a front end that can be probed while the instrument is off.
Published values
| Parameter | Value |
|---|---|
| Nonlinearity | 0.02 percent maximum, 0 V to 2 V rms input |
| Crest factor error | 0.1 percent additional error to a crest factor of 3 |
| Bandwidth at 2 V rms | 8 MHz |
| Bandwidth at 100 mV rms | 600 kHz |
| Functions | True rms, mean square, absolute value, dB output |
| dB range | 60 dB |
| External components | One capacitor sets averaging, low frequency accuracy, ripple and settling |
| Power down | Chip select pin, output goes high impedance |
| Input protection | Withstands overload beyond the supplies, survives loss of supplies |
| Body | Surface mount, R suffix |
One capacitor sets four things at once
The averaging capacitor is the whole time domain behaviour of the part: it sets the averaging period, the low frequency accuracy, the output ripple and the settling time, and those four move together. A large capacitor gives low ripple and good accuracy at 10 Hz but slows the response to a step, which is unacceptable in a level meter that has to track a fading signal. The data sheet gives the trade as a table rather than a formula, and the practical answer for bench instruments is a capacitor chosen for the lowest frequency of interest with a second, faster path for transients. Reading that table before choosing the capacitor is the difference between a converter that meets its 0.02 percent and one that shows 1 percent of ripple.
Crest factor is where average responding meters fail
An average responding meter calibrated to read rms is correct only for a sine wave, and a switching supply current or a pulse train has a crest factor far from 1.414. The crest factor specification here is stated as 0.1 percent of additional error up to 3 and the data sheet characterises the behaviour well beyond that, which is what allows this part to be used as the reference in a power analyser. For a buyer, the crest factor figure is the one to compare between rms converter families, because it is where the cheap parts and the instrument grade parts diverge most.
Availability and the surface mount body
The converter is still in production but it is not a high volume line, so stock moves in and out. The J grade in the surface mount body is the common industrial order code, and the same die is offered in other grades and packages for wider temperature work. Where a circuit has to keep the same measurement accuracy through a board revision, the averaging capacitor and its return path are the parts of the circuit worth keeping identical, because they set the accuracy far more than the body does. The amplifier cross reference lists the rms and detector families we supply, the ADI second source page covers equivalent grades, and the lead time page shows current stock positions.