Contact Us
  • Home
  • COMPONENTS
  • Audio Amplifiers for Class D and Headphone Stages

Audio Amplifiers for Class D and Headphone Stages

Class D parts give 15 W to 50 W per channel from a 4.5 V to 26 V rail at over 90 percent efficiency. A digital input amplifier takes I2S or TDM straight from the host and needs no DAC, no MCLK and no output filter. A headphone stage is a different job: low noise and high current into 32 ohm to 600 ohm, not raw watts. Every power figure is quoted at a stated load and supply, because none of them hold across the range.
quote now

Product Specifications

Product Overview

An audio output stage is chosen by the load it drives and the rail it has, and the numbers only mean something when both are attached. A class D amplifier switches its output between the rails at a few hundred kilohertz and relies on the speaker inductance to recover the waveform, which is why it reaches over 90 percent efficiency where a class AB stage reaches 50 to 60 percent. The TPA3116D2 family delivers 50 W per channel into 4 ohm from a 21 V rail, 30 W on the TPA3118D2 and 15 W on the TPA3110D2, all from the same 4.5 V to 26 V supply range and the same filter free modulation scheme.

The power figure falls quickly as the rail drops, and that is the number a battery or a 12 V product actually sees. A stage rated 50 W at 21 V into 4 ohm gives roughly a quarter of that at 12 V into the same load, because the output swing is limited by the rail. The right way to read a class D data sheet is to find the row where the supply and the load match the product, and to check the distortion at which the power is quoted, because a 10 percent THD figure is a clipping limit and a 1 percent figure is a usable one.

A digital input amplifier removes the analog path altogether. The MAX98357A takes I2S directly, recognises the clock scheme on its own without I2C programming, and needs no MCLK, so the host sends data and the amplifier produces 3.2 W into 4 ohm from a 5 V rail with 92 percent efficiency. It also removes the output filter: the edge rate control and the spread spectrum modulation keep the emissions low enough that the speaker leads can be driven without an LC network, which is a real saving in a small product. The MAX98357B is the same part with left justified data instead of I2S.

A headphone stage is a different set of requirements. The load is 16 ohm to 600 ohm rather than 4 ohm, the power is milliwatts rather than watts, and what matters is noise, crosstalk and the ability to drive a high impedance load without slew limiting. The TPA6120A2 is a current feedback amplifier with 1300 V per microsecond of slew rate that delivers 80 mW into 600 ohm from a plus or minus 12 V supply at 0.00014 percent THD plus N, with separate supplies per channel for crosstalk. Its supply range of plus or minus 5 V to plus or minus 15 V is what lets it swing the 2 V rms that a studio headphone expects.

The table below covers the parts we quote most often: the class D speaker families, the digital input amplifier and the headphone driver. Output power at a stated load and supply, supply range, efficiency, gain and package come from the maker data sheet for each code.

Key Specifications

ParameterClass D speaker, TPA3116D2Digital input, MAX98357AHeadphone, TPA6120A2
Output power50 W per channel into 4 ohm at 21 V, 30 W on the 3118, 15 W on the 31103.2 W into 4 ohm at 5 V80 mW into 600 ohm from plus or minus 12 V
Supply range4.5 V to 26 V2.5 V to 5.5 VPlus or minus 5 V to plus or minus 15 V
EfficiencyAbove 90 percent92 percent at 8 ohm, 1 WClass AB, set by the bias and the load
InputAnalog differentialI2S, left justified on the B version, TDM up to 8 slotsAnalog differential, current feedback
GainSet by the input networkFive settings from 3 dB to 15 dB by pin strapSet by the feedback network
DistortionQuoted with the power figure on the data sheet0.013 percent at 1 kHz, 0.5 W into 8 ohm0.00014 percent at 80 mW into 600 ohm
Quiescent currentSet by the switching stage and the modulation2.4 mASet by the bias of the output stage
Output filterFilter free modulation, LC optional for long leadsFilter free, no LC neededNot applicable
PackageHTSSOP and QFN power packages with thermal pad9 pin WLP or 16 pin TQFNSOIC-20 PowerPAD
Temperature-40 C to +85 C-40 C to +85 C-40 C to +85 C

Included Models and Order Codes

The table lists the codes we quote most often for active speakers, instrument panels and headphone outputs. Output power at a stated load and supply, supply range, efficiency, gain and package come from the maker data sheet for that code. A power figure without its load and its supply is not a specification, so both are carried on every line.

Part NumberClassOutput powerSupplyInputEfficiencyPackage
TPA3110D2Class D stereo15 W per channel into 8 ohm at 21 V4.5 V to 26 VAnalog differentialAbove 90 percentHTSSOP with thermal pad
TPA3118D2Class D stereo30 W per channel into 8 ohm at 24 V4.5 V to 26 VAnalog differentialAbove 90 percentHTSSOP with thermal pad
TPA3116D2Class D stereo50 W per channel into 4 ohm at 21 V4.5 V to 26 VAnalog differentialAbove 90 percentHTSSOP with thermal pad
MAX98357AClass D mono, digital input3.2 W into 4 ohm at 5 V2.5 V to 5.5 VI2S and TDM92 percent at 8 ohmWLP or TQFN
MAX98357BClass D mono, digital input3.2 W into 4 ohm at 5 V2.5 V to 5.5 VLeft justified and TDM92 percent at 8 ohmWLP or TQFN
TPA6120A2DWPClass AB headphone80 mW into 600 ohm from plus or minus 12 VPlus or minus 5 V to plus or minus 15 VAnalog differentialClass ABSOIC-20 PowerPAD
LM386M-1Class AB mono325 mW into 8 ohm at 6 V4 V to 12 VAnalog, ground referencedClass ABSOIC-8
LM386N-3Class AB mono700 mW into 8 ohm at 9 V4 V to 12 VAnalog, ground referencedClass ABDIP-8
LM386N-4Class AB mono1.0 W into 32 ohm at 16 V5 V to 18 VAnalog, ground referencedClass ABDIP-8

Key Features

Power quoted with load and supply – 50 W into 4 ohm at 21 V is a different product from 50 W into 8 ohm at 26 V, and the quotation keeps both conditions attached to the number.

Efficiency stated at a working point – above 90 percent on the class D family and 92 percent at 8 ohm and 1 W on the digital part, which is what the heatsink and the enclosure are sized against.

No MCLK and no I2C on the digital part – the MAX98357A recognises the clock scheme itself, so the host only supplies BCLK, LRCLK and data, and the gain is set by strapping a pin.

Filter free output – spread spectrum modulation with edge rate control keeps the speaker leads quiet enough that no LC filter is needed on short runs, which removes six parts per channel.

Gain set without firmware – five gain settings on the digital amplifier and an internal 1.35 kohm resistor on the LM386 mean the level is set at the board, not in code.

Current feedback headphone drive – 1300 V per microsecond of slew rate into a 600 ohm load is what keeps a 2 V rms signal clean at 20 kHz, where a voltage feedback part runs out of current.

Applications

These parts are quoted for products that have to make sound, typically where:

Active speakers and instrument amplifiers – a class D stereo stage from a 12 V to 24 V rail drives a pair of 4 ohm or 8 ohm drivers, and the filter free output keeps the board small inside the cabinet.

Voice prompts and alerts in instruments – a digital input amplifier takes the prompt straight from the host I2S bus, so there is no DAC, no analog trace and no output filter on the board.

Headphone and monitor outputs – a current feedback stage drives 32 ohm to 600 ohm headphones from a split rail, with the low distortion and the crosstalk that a monitoring path needs.

The output stage sits on the same board as the connectors and the supply, so it is quoted with the SUPERB PCB and the SUPERB PCBA build for that assembly.

Sourcing and Cross-Reference

Selection starts with the load and the rail, then with the thermal path. A class D part that delivers 50 W per channel into 4 ohm dissipates a few watts at that point, and the thermal pad, the copper area under it and the airflow decide whether the part stays inside its junction temperature. A part chosen for its power figure alone, without the thermal pad area on the board, will shut down at the first loud passage.

The second check is the input side. An analog input amplifier needs a differential pair routed as a pair, an input network that sets the gain and a supply that is quiet at the switching frequency. A digital input part needs the clock and data lines kept short and away from the speaker leads, and the sample rate has to be one the part accepts, because the I2S input does not take every LRCLK frequency. A headphone stage needs a split rail or a charge pump for the negative swing and a ground return that does not share the speaker current.

Where a code is short or has been replaced, the substitute is checked on output power at the same load and supply, supply range, input format, gain setting, thermal package and pin out at once. A part that matches the power but needs a different supply will not run on the existing rail, and a part that matches the pin out but has a lower thermal rating will pass the bench test and fold back in the enclosure. The route for that comparison is on our amplifier cross reference page, and the drop in check is on how to verify a drop in replacement.

For volume builds, SUPERB Assembly support covers the thermal pad reflow, the copper area under the package and the separation between the speaker leads and the input pair.

Q: Can you quote a 15 W class D part that runs from 12 V into 8 ohm, and confirm the thermal pad area the board needs?

A: Yes. Send the load, the rail, the power at the listening point and the enclosure, and the SUPERB Tech team will confirm the part, the gain setting and the thermal requirement from the maker data sheet before quoting.

Why Buyers Source Audio Amplifiers Through SUPERB

  1. Power always with load and supply: the quotation carries the condition, which is what stops a 21 V figure being carried into a 12 V product.
  2. Thermal path named: the package, the pad and the copper area are quoted together, because that is what the power figure depends on in a closed box.
  3. Input format checked against the host: I2S, left justified, TDM and analog inputs are listed per part, so the host interface is matched before the board is laid out.
  4. Cross reference on seven parameters: power, supply, input, gain, package, thermal rating and pin out are compared before a substitute amplifier is offered.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Amplifiers and comparators, Current sense amplifiers, Instrumentation amplifiers, Audio codecs, Piezo buzzers and audio indicators, Amplifier cross reference, Component lead time solutions.