Cable Markers and Wire Labels for Harness Identification
Product Specifications
Product Overview
There are two ways to identify a wire. One is to slide a pre-printed marker over it before termination, so the number is in the wire rather than on a label stuck to it. The other is to tie a printable tag to the bundle, so a long legend can be read without following the wire. The first is smaller, cheaper and permanent; the second carries more text and can be printed on site. Most panels use both, with the slide on marker for the wire and the tag for the bundle.
The slide on markers on this page are HellermannTyton Helagrip in three sizes. HGDC1-3 takes 1.0 to 3.0 mm bundles, is 3.5 mm long and 3.3 mm wide, and comes on a reel of 1000. HGDC2-5 takes 2.0 to 5.0 mm, is 3.5 mm long and comes on a reel of 1000. HGDC4-9 takes 4.0 to 9.0 mm, is 5.0 mm long and 6.8 mm wide, and comes on a reel of 250. The material is flexible PVC, cadmium free, rated from -65 to 105 C with an intermittent 135 C, and it is UL94 V0 at 3 mm.
The chevron cut is the detail that makes these markers work. Each marker is cut at an angle on both ends, so a row of them locks together and the text cannot rotate or part. That is why one size can fit a range of cables: the marker opens over the wire and closes on it, and a run of four characters holds itself in line. The characters are 0 to 9, A to Z and the standard electrical symbols, printed black on white or white on black, and each character has its own article number, so a legend is ordered as a set of characters rather than as a custom print.
The printable tags are the other half. The TIPTAG range is polyolefin, halogen free, rated from -40 to 90 C with a 160 C short term, and it is supplied on a perforated reel with slots for a cable tie up to 4.6 mm wide. The standard sizes are 11 mm by 65 mm, 15 mm by 65 mm, 11 mm by 100 mm and 15 mm by 100 mm, and the small TIPTAG5X50WH-2 is 5.5 mm by 50 mm with a 40 mm printable area for a wire down to a fibre. The print is thermal transfer, so the legend is printed on site from the drawing rather than ordered by the reel.
The bundle range is the figure that decides fit. A 2.0 to 5.0 mm marker on a 6 mm cable will not go on, and a 4.0 to 9.0 mm marker on a 2 mm wire slides along it. The length matters too: a 3.5 mm marker carries one or two characters comfortably, and a four character legend needs the 5.0 mm part or a tag. On a dense terminal block, the marker width also has to fit the pitch, because a 6.8 mm marker on a 5.2 mm terminal overlaps its neighbour.
The practical rules are about sequence. The markers are threaded onto the wire before the terminal is crimped, because a marker cannot pass a crimped ferrule. The legend is read back against the drawing before the loom is tied, because a marker that is one position out is harder to find after the bundle is closed. And the material has to suit the cleaning: PVC is fine for most solvents but not for a hot aromatic, and a marker that goes cloudy loses the legend before the panel leaves the line.
Key Specifications
| Parameter | Value | Applies to |
|---|---|---|
| Slide on bundle range | 1.0 to 3.0 mm, 2.0 to 5.0 mm, 4.0 to 9.0 mm | HGDC1-3, 2-5, 4-9 |
| Slide on length | 3.5 mm, 5.0 mm | By size |
| Slide on width | 3.3 mm, 6.8 mm | By size |
| Slide on material | Flexible PVC, cadmium free | Helagrip |
| Slide on temperature | -65 to 105 C, 135 C intermittent | Helagrip |
| Slide on flammability | UL94 V0 at 3 mm | Helagrip |
| Slide on characters | 0 to 9, A to Z, standard symbols | Helagrip |
| Slide on reel quantity | 1000, 1000, 250 | By size |
| Tag material | Polyolefin, halogen free | TIPTAG |
| Tag temperature | -40 to 90 C, 160 C for 200 h | TIPTAG |
| Tag sizes | 11 x 65 mm, 15 x 65 mm, 11 x 100 mm, 15 x 100 mm, 5.5 x 50 mm | By type |
| Tag fixing | Cable tie up to 4.6 mm wide | TIPTAG |
| Tag print method | Thermal transfer | TIPTAG |
Included Models and Order Codes
The rows below are the slide on markers we quote most often. Bundle range, length and reel quantity are given per type, because a marker that is one size out either will not go on the wire or slides along it.
| Type | Bundle Range | Length | Width | Material | Reel Quantity |
|---|---|---|---|---|---|
| HGDC1-3 | 1.0 to 3.0 mm | 3.5 mm | 3.3 mm | PVC, -65 to 105 C | 1000 |
| HGDC2-5 | 2.0 to 5.0 mm | 3.5 mm | - | PVC, -65 to 105 C | 1000 |
| HGDC4-9 | 4.0 to 9.0 mm | 5.0 mm | 6.8 mm | PVC, -65 to 105 C | 250 |
| HGDC1-3 character A | 1.0 to 3.0 mm | 3.5 mm | 3.3 mm | PVC, black on white | 1000 |
| HGDC1-3 character 0 | 1.0 to 3.0 mm | 3.5 mm | 3.3 mm | PVC, black on white | 1000 |
| HGDC4-9 character 9 | 4.0 to 9.0 mm | 5.0 mm | 6.8 mm | PVC, black on white | 250 |
Printable Cable Tags for Longer Legends
Tags carry a longer legend than a slide on marker and are printed on site. Size, printable area, material and the maximum tie width are given per type, because the tag has to be tied to the bundle rather than threaded over it.
| Type | Length | Width | Printable Area | Material | Pack |
|---|---|---|---|---|---|
| TIPTAG5X50WH-2 | 50 mm | 5.5 mm | 40 mm | Polyolefin, white | 500 |
| TIPTAG11X65WH | 65 mm | 11 mm | - | Polyolefin, white | 190 |
| TIPTAG11X65YE | 65 mm | 11 mm | - | Polyolefin, yellow | 190 |
| TIPTAG15X65WH | 65 mm | 15 mm | - | Polyolefin, white | 190 |
| TIPTAG11X100WH | 100 mm | 11 mm | - | Polyolefin, white | 120 |
| TIPTAG15X100WH | 100 mm | 15 mm | - | Polyolefin, white | 120 |
| TIPTAG15X100YE | 100 mm | 15 mm | - | Polyolefin, yellow | 120 |
Key Features
Bundle range per type – Three overlapping ranges cover 1.0 mm to 9.0 mm wire and cable, so a marker is not ordered by length alone.
Chevron cut locking – The angled cut locks a row of markers together, so a four character legend cannot rotate or part on the wire.
Temperature to 105 C – The PVC markers are rated from -65 to 105 C with an intermittent 135 C, which covers a cabinet and a machine frame.
V0 flammability – The slide on markers are UL94 V0 at 3 mm, which matters inside a cabinet that has to meet a flame requirement.
Printable tags on site – The polyolefin tags print by thermal transfer from the drawing, so a legend change does not need a new reel order.
Tie width stated – The tags take a cable tie up to 4.6 mm wide, which is the figure that decides whether a standard T50R tie fits.
Applications
These parts are used on panel wiring, machine looms and rack cables where a wire has to be identified at both ends.
Panel and cabinet wiring – A 2.0 to 5.0 mm marker over a 2.5 mm wire keeps a four character legend in line, and the V0 material suits a cabinet that has a flame requirement.
Machine harnesses – A 4.0 to 9.0 mm marker on a 6 mm bundle is 5.0 mm long and 6.8 mm wide, so a two character legend is readable without a tag.
Rack and data cables – A 15 by 100 mm tag tied with a 4.6 mm tie carries a full circuit reference where a slide on marker would be too small to read.
A marker is only useful if it is still readable after the harness is dressed, so the material is checked against the SUPERB PCB service temperature and the cleaning solvents on the line. On the SUPERB PCBA route the markers go on before the loom is tied, because a marker fitted after the tie is a marker that sits on the wrong side of the bundle.
Sourcing and Cross-Reference
A marker is bought by bundle and by legend. The bundle range is on the data sheet and the legend is on the drawing, and the two have to be matched before the reel is ordered, because a character can only be supplied in the sizes that exist. When a marker is replaced on a loom that is already built, the wire diameter and the number of characters are the two figures to send.
The second point is the material. PVC is flexible, cheap and rated to 105 C, but it is not the part for a hot engine bay or a solvent wash. Polyolefin tags take more heat and print more sharply, and the halogen free grade is the one that a rail or an aerospace build asks for. A marker that goes cloudy or brittle loses the legend, which is the same as no marker at all.
The third point is sequence and readability. Markers are threaded before the terminal is crimped, read back against the drawing before the loom is tied, and fitted so the text faces the inspection side of the panel. A dense terminal block also needs the marker width checked against the pitch, because a 6.8 mm marker on a 5.2 mm terminal covers the next pole. We quote the marker and the tag together, because a loom usually needs both.
SUPERB Assembly builds the first loom with the markers already threaded, then reads every legend back against the drawing, because a marker that was cut and fitted afterwards is a marker that can end up on the wrong wire.
Q: Can you supply slide on markers for 2.0 to 5.0 mm wire with a four character legend, plus printable tags for the bundle ends in the same order?
A: Send the wire range, the character set and whether the legend is printed or pre-printed. The SUPERB Tech desk quotes the marker with its bundle range and its length, because a 1 to 3 mm marker will not go over a 4 mm cable and a 4 to 9 mm marker will slide on a 2 mm wire.
Why Buy Cable Markers and Wire Labels Through SUPERB
- Bundle range checked first: Markers are quoted by the wire they go on, which is where a 4.0 to 9.0 mm part gets ordered for a 2 mm wire.
- Material matched to the heat: PVC to 105 C and halogen free polyolefin tags are both on the page, so a hot or a rail build is not forced onto the same part.
- Character set and sizes: The 0 to 9 and A to Z range is quoted per size, because a four character legend needs the 5.0 mm marker or a tag.
- Read back before tying: The first loom is read against the drawing before the bundle is closed, because a marker one position out is hard to find later.
- Markers and tags together: The slide on marker and the tie on tag are quoted as one set, because a loom usually needs both.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Heat Shrink Tubing and Sleeves for Harness Protection, Braided Sleeving and Expandable Sleeves for Harness Protection, Cable Clamps and Harness Ties for Internal Wiring, Wire Ferrules and Crimp Sleeves for Terminal Blocks, Screw Terminal Blocks and Pluggable Connectors for Field Wiring, BOM Shortage Recovery.