Contact Us
  • Home
  • BLOG
  • How Much Current Can a Plated Via Carry?

How Much Current Can a Plated Via Carry?

For a 0.30 mm drill with 20 um of copper in the barrel, the wall carries 0.76 A at a 10 C rise if the via runs between planes, and 1.53 A if it runs on an outer surface. The number that gets repeated in stack-up reviews, one amp per 0.3 mm via, sits next to the outer-surface figure. Most power vias are not on an outer surface. Start at 0.76 A and then decide whether the local heat path buys you more.

Nothing else in the via carries current. The pad is a landing and so is the annular ring. The plane the via lands on is a wide conductor. What is left is a thin copper tube, so the whole DC question is how thick that tube is and how much heat it can shed.

The arithmetic, in one line

barrel section = 3.14 x drill x plating thickness. For a 0.30 mm drill and 20 um of copper that is 3.14 x 0.30 x 0.020 = 0.0188 square mm, or 29 square mils. That is the same copper as 0.54 mm of 1 oz trace, and it is the number that belongs in a current table.

DrillSection at 20 umBetween planesOn a surface
0.20 mm0.0126 mm2 (19.5 mil2)0.57 A1.14 A
0.25 mm0.0157 mm2 (24.3 mil2)0.67 A1.34 A
0.30 mm0.0188 mm2 (29.2 mil2)0.76 A1.53 A
0.50 mm0.0314 mm2 (48.7 mil2)1.11 A2.21 A
0.80 mm0.0503 mm2 (77.9 mil2)1.55 A3.11 A

The resistance is not the problem. On a 1.6 mm board, 0.0188 mm2 of copper is 1.46 milliohms end to end. At 2 A the drop is 2.9 mV and the barrel dissipates 5.8 mW. At 5 A it is 7.3 mV and 36 mW. On a surface trace those numbers would be trivial. What makes them matter is where the heat goes: the barrel sits inside laminate with a thermal conductivity near 0.3 W/(m K), and its outer surface is about 1.5 mm2 on a 1.6 mm board. A surface trace of the same section has air on one side and copper on the other. That difference is most of the gap between the two current columns.

Why a row of vias does not add up

Ten vias do not give ten times the current. Two effects eat the sum. The first is spreading: current enters the plane at the edge of the antipad and has to fan out through the plane's own copper, so if the vias sit in a tight cluster the ones nearest the source do most of the work. The second is plating thickness, which varies across the panel and across the barrel, so the weakest tube sets the limit for the group.

The practical rule is to place the vias along the current path rather than in a cluster, and to derate the arithmetic sum by 20 to 30%. A transition that needs 5 A is five 0.30 mm vias at 0.76 A each, which is 3.8 A on paper and about 3 A in copper.

Thermal relief is the other place the number disappears. Four spokes 0.20 mm wide on 1 oz copper come to 0.028 mm2, one and a half barrels. A via in a relief has its heat path cut at the same time as its current path, which is why the same via that runs cool in solid copper runs hot in a thermal pad.

Three things that go wrong

Using the outer-surface curve. The published ampacity curves come in two families, and the internal one is half the external one for the same section. Taking the external number for a via between planes, then running it at 90% of the result, is a factor of two in the wrong direction.

Reading the plating thickness off the pad. Our published figure is 20 um minimum, and it is a minimum for the barrel rather than the surface. The middle of a 1.6 mm barrel is always the thinnest point because the plating has to throw current down the hole. If a via has to pass 0.9 A, the question is what the wall measures at mid-barrel, not what the drawing says.

Counting the pad as conductor. A 0.528 mm pad looks like a lot of copper next to a 0.30 mm tube. Current turns 90 degrees at the pad and the pad adds little to the path. What matters is the copper weight of the plane around the antipad, because the current crosses that plane through a ring, not through the whole sheet.

When the answer is a different structure

Above roughly 5 A per transition the arithmetic stops being about vias. Either the current moves on a copper bar or a heavy copper layer, or the transition is spread along the whole edge of a pour, where each via carries a fraction of an amp and the group is limited by the spreading resistance of the plane rather than by any single tube. On the power boards we build, 4 oz to 10 oz outer copper with stitched edges is the normal answer for 20 A and above.

What SUPERB PCB controls in the barrel

Published plating is 20 um minimum, with a 10 um maximum recess on a filled via. Mechanical drills run 0.15 to 6.35 mm, laser drills 0.075 to 0.15 mm, aspect ratio 10:1 on the standard line and up to 25:1 on the high-layer line, hole position tolerance 0.075 mm, copper up to 6 oz inner and 10 oz outer where the current needs it. A slice report on request shows the wall at the top, middle and bottom of the barrel, which is the only way to answer the mid-barrel question with a measurement instead of a promise.

SUPERB Tech checks three things on every power via: the copper in the barrel, the copper in the plane it lands on, and the number of vias sharing the path. Limits are on the PCB capability page, the high current side is on heavy copper PCB, and the plating side is covered in how thick the copper in a plated hole should be.

One honest limit: the table above is a steady-state DC table. A via carrying 3 A at 10% duty is a different problem from one carrying 3 A continuously, and the newer charts allow more current for the same rise in still air than the older curve we quote. We quote the tighter curve and say so, because a via that is marginal on paper is the one that comes back discoloured after a year in the field.

What to send with the question

Current per via and whether it is DC or pulsed with a duty cycle, the temperature rise you will accept, board thickness, how many vias share the path, whether any of them sit in a thermal relief, the copper weight of the planes they connect, and the air around the board. With those seven numbers the answer is a calculation instead of a rule of thumb, and the rule of thumb stops being the thing that decides the layout.

Need a quote or a review of your stack against these limits? pcba@superb-tech.com · WhatsApp +86 133 9608 1443