Contact Us

UCD9090ARGZR

Brand: Texas Instruments
Texas Instruments UCD9090ARGZR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCD9090ARGZR — Power Management & Signal Chain | Superb Automation

UCD9090ARGZR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCD9090ARGZR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCD9090ARGZR: ten rails sequenced and monitored through one PMBus address

The UCD9090A is a ten rail power supply sequencer and monitor in a 48 pin VQFN body. It holds the turn on and turn off order for up to ten rails, watches each rail through its own VMON pin into a 12 bit ADC, and exposes the whole arrangement on a PMBus and I2C interface that runs to 2 MHz. Twenty three GPIO pins carry the enable lines, power good inputs, reset signals, a watchdog input, cascading between several sequencers and PWM outputs that can trim a converter. Configuration lives in the device's own non volatile memory, so a finished board comes up in the right order without a host processor having to load a register map at every power cycle.

The A suffix matters. The UCD9090A adds ACPI support to the earlier part, which is what a telecom or server chassis needs when the operating system asks for a sleep state and the rails have to fall in a defined order rather than all at once. Fault handling is programmable per rail: an out of window condition can trigger a shut down, a retry, or a coordinated response that brings down a group of rails together. The ADC also supports margining, so a production test can push a rail plus or minus a few per cent and confirm the load still behaves, and the margin thresholds are stored alongside the sequence rather than being computed on the fly.

Key data for the UCD9090ARGZR

RailsTen monitored rails, ten VMON inputs, 12 bit ADC on each, user defined under and over voltage windows
InterfacePMBus and I2C up to 2 MHz, address set by pin strapping, non volatile configuration and fault log
GPIOTwenty three pins for enables, power good, resets, watchdog, cascade in and out, and PWM trimming
MarginingClosed loop margining on the rails plus general purpose PWM outputs for converters that need it
Supply3.3 V core and IO, separate 12 V rail for the gate drive and the monitoring front end in most builds
TemperatureJunction range minus 40 C to 125 C on the published orderable rows

Body, marking and reel data

BodyRGZ, VQFN 48 pin, 7 mm by 7 mm with a thermal pad, 0.5 mm pitch
ReelUCD9090ARGZR is 2500 pieces on a large reel, UCD9090ARGZT is 250 pieces on a small reel
FinishNIPDAU on the published rows, moisture level 3 with a 168 hour floor life at 260 C
SuffixThe plain string and the .A and .B rows of the same string all ship the same silicon
AmbientMinus 40 C to 125 C junction on every active row, no commercial only grade in the family

Where a ten rail sequencer earns its cost

A board with one regulator does not need this part. A board with a processor, two DDR rails, a serializer, an analogue front end and a radio module does, because the order in which those rails appear decides whether the processor latches up on the first power cycle or on the tenth. The classic failure is a core rail arriving before the IO rail, which forward biases an internal protection diode and holds the supply in a brown out until the sequencer resets. Hard wiring the enables in a chain works until one rail is slow, and then the timing margin disappears in cold start. The sequencer replaces that chain with a stored table and gives the fault log that shows which rail came up late.

On the sourcing side, this part is usually bought once per board for a long production life, so the risk is not the first order but the fifth year. Where a customer is moving an existing product to a new revision, our power management cross reference covers the sequencer and monitor families that share the PMBus command set, and the obsolescence management page sets out how we hold a last time buy for a controller that sits in the power up path.

Buyer questions on the UCD9090ARGZR

Can the ten rails be sequenced in any order? Yes. Each rail has its own turn on delay and its own dependencies, and the table is written into non volatile memory through the PMBus interface. The cascade pins let two or three devices act as one sequence where a board has more than ten rails.

Does the part need a host processor to work? No. Once the configuration is stored it runs from its own memory at every power up. The processor is only needed to change the sequence, read the fault log, or issue a margining command during test.

What is the difference between the R and T reel suffix? The R row is 2500 pieces on a large reel and the T row is 250 pieces on a small reel. The silicon is the same, so a prototype build can use the small reel and the production order move to the large one without a change note.

Availability and ordering notes

The 48 pin VQFN has a thermal pad that must be soldered to a copper area connected to ground, otherwise the junction runs hotter than the calculation assumes. The moisture level 3 rating means the reel has a 168 hour floor life once the bag is opened at 260 C, so a line that builds in small batches needs either a dry cabinet or a bake before the second week. Both the reel size and the floor life go on our quote, and where a build is waiting on the sequencer alone we can kit the part against the rest of the BOM through the kitting service.