UCC38C44DR
Product Specifications
UCC38C44DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC38C44DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC38C44DR: half duty current mode control for a forward converter, in a taped SOIC
The UCC38C44DR is the half duty member of the UCCx8C4x family at commercial temperature. It turns on at 14.5 V and off at 9 V, reaches about 48 percent duty because the output stage toggles on alternate oscillator cycles, and carries the same 1 A totem pole drive, 35 ns current sense delay and 1 percent 5 V reference as the rest of the family. The half cycle limit is what a single ended forward converter needs so the transformer core can reset through the reset winding during the off time, and it is what a push pull stage imposes by construction.
The electrical improvements over the bipolar UC3844 it replaces are worth repeating because they change the external network. Start up current drops to 50 microamps, so a start up resistor off a 400 V rail dissipates well under a tenth of a watt while the controller waits. The oscillator discharge current is trimmed, so the maximum duty and the dead time do not wander with process, which matters when the reset time has to be guaranteed at the worst case corner. And the current sense to output delay of 35 ns means a short circuit is caught before the drain current reaches its peak.
Key electrical data for the UCC38C44DR
| Supply | Start up 50 microamps typical and 100 microamps maximum, run current 2.3 mA at 52 kHz |
| Lockout | Turn on 14.5 V, turn off 9 V, the off line window in the family |
| Reference | 5 V at 1 percent initial accuracy, error amplifier reference 2.5 V |
| Output | 1 A peak totem pole, 25 ns rise, 20 ns fall, 35 ns current sense to output |
| Duty | 47 percent minimum and 48 percent typical maximum, output frequency half the oscillator |
| Temperature | 0 C to 85 C on this grade, minus 40 C to 125 C on the UCC28C44 sibling |
Package, marking and reel data
| Body | D, SOIC 8 pin, marking 38C44 |
| Reel | 2500 pieces on a 330 mm reel, 12.4 mm carrier, quadrant Q1 |
| Finish | NIPDAU at moisture level 1 unlimited on the plain row |
| Note | The .A row of the same string prints an 80 piece tube rather than a reel |
The .A row is a tube, not a reel
An R in the suffix normally means tape and reel, and on this string the .A row breaks that rule: it prints 80 pieces in a tube. A buyer who assumes the R is the packing and orders the .A row for a production build receives tubes, and the placement machine cannot be loaded from a tube without a conversion. The plain row is the 2500 piece reel. That is the sort of detail that only shows up when the goods arrive, which is why we quote the row and the packing rather than the short string.
The other point is the duty limit against the transformer. A forward converter built around this part must have a reset arrangement that clears the core within the off time at maximum duty, and the worst case is at high line with the loop at its limit. A 48 percent limit leaves just over half a cycle for reset, which is comfortable for a single ended forward and tight for a converter that also has to handle a wide input range. A leakage inductance that is too high for the available reset time shows up as a rising core temperature at high line rather than as a regulation fault, so the thermal check belongs in the qualification rather than in the field. Our power management cross reference page lists the family so the duty limit can be matched to the topology before a part is chosen.
Buyer questions on the UCC38C44DR
Is the reel size the same as the UCC38C42DR? The plain row is 2500 pieces on both. What differs is the .A row of this string, which prints 80 pieces in a tube rather than a reel.
Can this drive a large MOSFET directly? It charges the gate at 1 A peak, which suits a part with tens of nanocoulombs of gate charge. A larger device needs a buffer stage between the controller and the gate.
Does the 9 V turn off threshold suit a 12 V bias? It does, with 3 V of margin. A bias that sags below 9 V during a load step will reset the controller, so the hold up capacitor has to cover that window.
Availability and cross reference
Both rows are active, and the difference between them is the packing rather than the silicon. We hold the reel row for production and the tube row for sample and repair work, and the warehouse records which one went out on every shipment. The substitution check against the full duty member is on our kitting service page, because a duty limit mistake is invisible until the converter saturates.