UCC3802DTR
Product Specifications
UCC3802DTR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC3802DTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC3802DTR: full duty current mode control with a 12.5 V lockout, in a taped SOIC
The UCC3802DTR is the 100 percent duty member of the UCC280x family with the off line lockout: 12.5 V on and 8.3 V off. Start up current is 100 microamps typical, run current is 500 microamps, and the output is a 1 A totem pole stage with 70 ns from current sense to gate drive. The family is the BiCMOS successor to the UC3842 and keeps the pinout, while adding an internal full cycle soft start and internal leading edge blanking on the current sense input. The reference is 5 V at 1.5 percent and the error amplifier sits at half of it.
Full duty matters in a boost or a flyback that has to hold regulation when the input falls close to the output, and it is also what a SEPIC needs at the bottom of its range. The -04 member carries the same lockout with the toggle latch limiting duty to half a cycle, so the two codes differ in exactly one internal connection and cannot be interchanged without checking the topology. The 70 ns blanking window is the other reason to take this family over a UC3842: the leading edge spike from the gate charge does not reach the comparator, so the RC filter that the older circuits carry on the sense line can be removed.
Key electrical data for the UCC3802DTR
| Supply | Start up 100 microamps typical, run current 500 microamps typical, operation to 1 MHz |
| Lockout | Turn on 12.5 V, turn off 8.3 V, the off line option in the family |
| Reference | 5 V at 1.5 percent tolerance, error amplifier input at 2.5 V |
| Output | 1 A totem pole gate drive, actively held low while the supply is below the lockout |
| Timing | 70 ns typical from current sense to gate drive, internal leading edge blanking |
| Duty | 100 percent maximum, the full range member of the family |
Package, marking and reel data
| Body | D, SOIC 8 pin, marking UCC3802, ambient 0 C to 70 C |
| Reel | 2500 pieces on a 330 mm reel, 12.4 mm carrier, quadrant Q1 |
| Finish | NIPDAU, with the plain row printing Call TI in the moisture level field and the .A row printing level 1 unlimited |
| Sibling | UCC2802 is the same silicon at minus 40 C to 125 C, and the 1802 is the automotive grade |
Why the temperature grade is the first thing to read on this family
The same eight pin function exists in three temperature grades, and the part number prefix tells you which: UCC180x for the automotive and high temperature range, UCC280x for the industrial range, and UCC380x for the commercial range. The addendum row for this code prints 0 C to 70 C, which is narrower than most industrial products allow, and a build that assumes minus 40 C from the family datasheet will fail at the qualification step rather than at the bench. The electrical behaviour and the pinout are identical across the grades, so the change is a suffix rather than a board change, and the reel size stays at 2500 pieces on all three, which means the feeder setup and the material handling record do not change either.
The soft start is internal and runs as a full cycle ramp, which means the first cycles after power up come up with a duty that rises from zero instead of jumping to the loop's demand. That removes the transformer stair step that a bipolar controller produces without an external capacitor on the compensation pin, and it also keeps the inrush into the output capacitor inside the current limit. Our power management cross reference page lists the three grades and the bodies they share.
Buyer questions on the UCC3802DTR
Can this replace a UC3842 directly? The pinout is the same and the vendor states the family as the replacement. The internal soft start and the leading edge blanking change the external network rather than the footprint.
What is the difference from the UCC3804? Only the duty limit. The 802 reaches 100 percent, the 804 stops at about half a cycle through the toggle latch. The lockout and the reference are the same.
Is the commercial temperature range enough for an industrial product? It is 0 C to 70 C, which is narrower than most industrial products allow. The UCC2802 carries the same function at minus 40 C to 125 C.
Availability and cross reference
The reels are 2500 pieces and the three grades share one body, so a change of grade keeps the footprint. We hold the commercial and industrial grades and quote the suffix explicitly, because the addendum prints the same family name across all three and the only visible difference is the prefix. The handling rules for a part that moves between grades are on our date code management page.