UCC37325DR
Product Specifications
UCC37325DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC37325DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC37325DR: two 4 A low side channels, one inverting and one not, in an eight pin SOIC
The UCC37325DR is a dual channel low side MOSFET driver with a 4 A peak output, one inverting input and one non-inverting input, and a supply range of 4.5 V to 15 V. It is the industrial temperature member of the UCCx732x family, where the 3 prefix denotes the commercial grade and the 2 prefix a different die. The output stage is BiCMOS and holds a constant current into the Miller plateau even when the supply is low, which is the reason the part is quoted at 4 A rather than at a switching time: the gate charge is removed at a defined current instead of through a resistor that loses its drive as VDD falls.
Three input arrangements share the body. The 323 is dual inverting, the 324 dual non-inverting, and the 325 one of each, so a half bridge can be driven from a single logic signal with no external inverter. Input thresholds are 1.6 V to 2.5 V for a high and 0.8 V to 1.5 V for a low, which suits 3.3 V logic, and the quiescent supply current is 300 microamps to 450 microamps depending on the input states. Rise time is 20 ns and fall time 15 ns into a 1.8 nF load, with 25 ns of delay on a rising input and 35 ns on a falling one.
Key electrical data for the UCC37325DR
| Supply | 4.5 V to 15 V recommended operating range, 16 V absolute maximum on VDD |
| Drive | 4 A peak output at 14 V, 0.6 ohm pull up and 0.4 ohm pull down typical at 10 mA |
| Inputs | High 1.6 V to 2.5 V, low 0.8 V to 1.5 V, TTL and CMOS compatible, one inverting and one non-inverting |
| Timing | 20 ns rise and 15 ns fall into 1.8 nF, 25 ns delay on a rising input, 35 ns on a falling input |
| Quiescent | 300 to 450 microamps static, 600 to 750 microamps with both inputs high on the 324 member |
| Temperature | Ambient 0 C to 70 C on the UCC37325 rows, minus 40 C to 85 C on the UCC27325 rows |
Package, marking and reel data
| Body | D, SOIC 8 pin, marking 37325 |
| Reel | 2500 pieces on a 330 mm reel, large tape and reel |
| Finish | NIPDAU at moisture level 1 unlimited on both the plain and the .A row |
| Alternative | The PowerPAD MSOP body lowers the thermal resistance for continuous high frequency drive |
Constant current drive is the point of the family
A conventional CMOS driver behaves like a resistor, so the gate current falls as the gate voltage rises toward the rail, and the last volt of the Miller plateau takes as long as the first. This family holds a current source through that region, which shortens the plateau and reduces the switching loss in the MOSFET without changing the gate resistor. At 4 A the effect is visible on a 100 nC gate: the plateau collapses in tens of nanoseconds rather than hundreds, and the drain voltage and current cross with less overlap.
The mixed polarity input is the practical convenience. Feed one logic signal into both pins and the two outputs move in opposite directions with a delay difference of 10 ns between the rising and falling paths, which is inside the dead time a controller already inserts. Where the timing matters more closely, the two inputs can be driven separately from a controller that provides its own dead time. Our pin to pin cross reference page lists the three members and the bodies that share the pinout.
Buyer questions on the UCC37325DR
Why is this called a 4 A driver when the datasheet quotes 4 A at 14 V? The peak current is specified at a 14 V supply into a capacitive load. At a 5 V supply the peak is lower, but the constant current behaviour keeps the plateau drive predictable.
Can the two outputs be paralleled? The vendor states that the outputs may be paralleled for higher drive current. Join them at the pins and keep the gate loop short so the two halves do not see different inductance.
What is the difference between the 2 and the 3 prefix? The UCC2732x is rated from minus 40 C to 85 C and the UCC3732x from 0 C to 70 C. The electrical set is the same, so the choice follows the ambient range of the product.
Availability and cross reference
The SOIC body ships 2500 pieces on a reel and the PowerPAD MSOP body is the option when the driver runs hot. Because the family covers three input arrangements in one pinout, a board can change polarity without a change of footprint, which matters during a re-spin when the controller output polarity turns out to be the opposite of what was assumed. We hold all three and quote the body with the code, and the substitution check is on our how to verify a drop in replacement page.