Contact Us

UCC28250PWR

Brand: Texas Instruments
Texas Instruments UCC28250PWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC28250PWR — Power Management & Signal Chain | Superb Automation

UCC28250PWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC28250PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC28250PWR: a bridge controller that starts into a prebiased output and drives synchronous rectifiers

The UCC28250PWR is an advanced pulse width modulation controller for half bridge, full bridge, interleaved forward and push pull converters. Its distinguishing feature is prebiased start up: the controller can bring a converter up while the output capacitor is already charged, which happens in a parallel redundant supply or when a second rail holds the node up. It also drives synchronous rectifier control outputs with independently programmable delays, including a zero delay setting, so the rectifier timing can be matched to the transformer and the primary switches rather than set by a fixed internal number.

The control path can be voltage mode with input voltage feedforward or current mode, and the controller can sit on the primary or the secondary side of the isolation barrier. That flexibility is why the same part appears in telecom, server and industrial supplies: a secondary side arrangement puts the error amplifier next to the output divider and removes the optocoupler, while a primary side arrangement keeps the isolation in one place. The oscillator runs to 2 MHz, which is 1 MHz of switching frequency at each output, and the cycle by cycle overcurrent comparator is specified to 1 percent with matched duty cycle outputs.

Key electrical data for the UCC28250PWR

Reference3.3 V output, 3.22 V to 3.38 V window, which is 1.5 percent
LockoutStart threshold 4.0 V to 4.6 V with 4.3 V typical, start up current 150 microamps typical
FrequencyOscillator to 2 MHz, equivalent to 1 MHz of switching frequency, synchronisable to an external clock
OutputsTwo primary outputs plus two synchronous rectifier outputs with programmable delays and zero delay support
Protection1 percent accurate cycle by cycle overcurrent, programmable soft start, hiccup restart timer
ControlVoltage mode with input voltage feedforward, or current mode, primary or secondary side

Package, marking and reel data

BodyPW, TSSOP 20 pin, 6.50 mm by 4.40 mm, marked UCC28250
Reel2000 pieces on a 330 mm reel, 16.4 mm carrier, quadrant Q1
FinishNIPDAU, moisture level 1 at 260 C unlimited on the reel row
SiblingThe VQFN 20 body is 4.00 mm by 3.50 mm and carries the same silicon

Prebias start up is a system feature, not a datasheet line

Most controllers that claim prebias operation simply hold the outputs off until the internal ramp passes the feedback level, and the output rises from wherever it was. The arrangement here is more deliberate: the controller compares the feedback against the reference and only allows the primary switches to move when the loop can take over without pulling the output down. That matters in a redundant supply, where one unit is hot and the second is switched on into a live bus, and it matters in a battery backed product where a charger holds the rail up while the converter starts. Without it, the second unit discharges the bus through its own rectifiers for a few milliseconds, and the first unit sees a load step it was not built for.

The synchronous rectifier delays are the other half of the same problem. A rectifier that turns on too early shorts the transformer, and one that turns on too late loses efficiency in its body diode. The programmable delay lets the timing be moved for each build, and the zero delay setting covers a topology where the primary and the rectifier are meant to switch together. Our power management cross reference page lists the half bridge drivers the vendor pairs with this controller.

Buyer questions on the UCC28250PWR

Does the controller include the gate drivers? No. It provides the control outputs and the rectifier timing, and the vendor's application circuit pairs it with a half bridge driver and a dual low side driver. Those parts are separate codes.

Can it run from a 4.5 V bias? The start threshold is nominally 4.3 V, so a 4.5 V rail sits only 200 mV above it. A bias with any sag at start up needs more headroom than that.

What does secondary side control change? It moves the error amplifier next to the output and removes the optocoupler, at the cost of bringing the controller's own bias across the barrier. The part supports both arrangements with the same pinout.

Availability and cross reference

The TSSOP body ships 2000 pieces on a reel and the VQFN body shares the silicon, so the choice between them is a thermal and a footprint decision rather than an electrical one. Both print NIPDAU at moisture level 1 on the reel rows. Because this controller is usually the longest lead item in a bridge supply, we hold it against a forecast rather than against an order, and the exposure plan is on our safety stock planning page.